9J5106 KIT (Seal) Caterpillar parts
631C, 633D, 641, 641B, 824B, 988
Rating:
Alternative (cross code) number:
CA9J5106
9J-5106
9J5106
CA9J5106
9J-5106
9J5106
Weight: 0.010 pounds 0 kg.
WHEEL DOZER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 9J5106:
Information:
Remove Crankshaft Front Seal & Wear Sleeve
Start By:a. remove vibration damper and pulley 1. Use a punch or Tool (A) to put a hole in seal (1). Use Tool (A) to remove seal (1) from the timing gear cover. When a replacement of the front seal is made, a replacement of the wear sleeve is to be made also. 2. Put Tool (B) in position in the seal bore as shown.3. Install Tool (C) between Tool (B) and the wear sleeve. Turn Tool (C) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove Tool (B) and the wear sleeve by hand.Install Crankshaft Front Seal & Wear Sleeve
The wear sleeve and seal must be installed at the same time.1. Install the crankshaft front seal and wear sleeve with Tool (A) as follows:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V-1541 Quick Cure Primer. Make an application of 9S-3265 Retaining Compound to crankshaft outside diameter and wear sleeve inside diameter before the wear sleeve is installed on the crankshaft.b. Install locator (1) and the bolts on the front of the crankshaft.c. The wear sleeve and seal come as a set with the seal already installed on the wear sleeve. Make sure the lip of the seal is toward the inside of the engine as shown and the outside diameter bevel of the wear sleeve is toward the outside of the engine.d. Put the wear sleeve and seal in position on locator (1). e. Put installer (2) in position on locator (1).f. Put clean engine oil on the face of nut (3) and its contact area on installer (2). Install nut (3) on stud of locator (1).g. Tighten nut (3) until the inside surface of installer (2) comes in contact with locator (1).h. Remove Tool (A) and check the wear sleeve and seal for correct installation.End By:a. install vibration damper and pulley
Start By:a. remove vibration damper and pulley 1. Use a punch or Tool (A) to put a hole in seal (1). Use Tool (A) to remove seal (1) from the timing gear cover. When a replacement of the front seal is made, a replacement of the wear sleeve is to be made also. 2. Put Tool (B) in position in the seal bore as shown.3. Install Tool (C) between Tool (B) and the wear sleeve. Turn Tool (C) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove Tool (B) and the wear sleeve by hand.Install Crankshaft Front Seal & Wear Sleeve
The wear sleeve and seal must be installed at the same time.1. Install the crankshaft front seal and wear sleeve with Tool (A) as follows:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V-1541 Quick Cure Primer. Make an application of 9S-3265 Retaining Compound to crankshaft outside diameter and wear sleeve inside diameter before the wear sleeve is installed on the crankshaft.b. Install locator (1) and the bolts on the front of the crankshaft.c. The wear sleeve and seal come as a set with the seal already installed on the wear sleeve. Make sure the lip of the seal is toward the inside of the engine as shown and the outside diameter bevel of the wear sleeve is toward the outside of the engine.d. Put the wear sleeve and seal in position on locator (1). e. Put installer (2) in position on locator (1).f. Put clean engine oil on the face of nut (3) and its contact area on installer (2). Install nut (3) on stud of locator (1).g. Tighten nut (3) until the inside surface of installer (2) comes in contact with locator (1).h. Remove Tool (A) and check the wear sleeve and seal for correct installation.End By:a. install vibration damper and pulley
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
1U0379
KIT-FLEX PLATE
153, 173B, 518, 518C, 528, 528B, 530B, 561H, 561M, 572G, 613B, 613C, 613C II, 615, 615C, 623B, 631C, 633D, 814B, 815B, 824C, 825C, 844, 844H, 916, 920, 926, 936, 936F, 950, 950B, 950B/950E, 953, 973, ...
153, 173B, 518, 518C, 528, 528B, 530B, 561H, 561M, 572G, 613B, 613C, 613C II, 615, 615C, 623B, 631C, 633D, 814B, 815B, 824C, 825C, 844, 844H, 916, 920, 926, 936, 936F, 950, 950B, 950B/950E, 953, 973, ...
1U0378
KIT-FLEXPLATE
173B, 183B, 528, 528B, 530B, 561H, 561M, 613B, 613C, 613C II, 631C, 633D, 651E, 657E, 657G, 916, 920, 926, 930, 930R, D250B, D300B, D7G, FB518, IT18, IT28, IT28B
173B, 183B, 528, 528B, 530B, 561H, 561M, 613B, 613C, 613C II, 631C, 633D, 651E, 657E, 657G, 916, 920, 926, 930, 930R, D250B, D300B, D7G, FB518, IT18, IT28, IT28B
8J0420
KIT-SEAL
518C, 528, 528B, 530B, 623, 627, 627B, 637D, 641B, 657B, 920, 926, 930, 950, 966C, D3
518C, 528, 528B, 530B, 623, 627, 627B, 637D, 641B, 657B, 920, 926, 930, 950, 966C, D3
4J8489
KIT (CARTRIDGE)
16, 172, 183B, 641
16, 172, 183B, 641
9J5111
KIT (seal)
140, 16, 191, 631C, 633C, 633D, 769, 941, 951B, 980B, 988
140, 16, 191, 631C, 633C, 633D, 769, 941, 951B, 980B, 988
9J5108
KIT (seal)
621, 621B, 623, 623B, 627B, 633D, 641B, 772, 966C, 983, 992
621, 621B, 623, 623B, 627B, 633D, 641B, 772, 966C, 983, 992
2G7182
KIT-CARTRIDGE
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
2G7183
KIT-REFILL
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
2G7184
KIT-PURGE VALVE
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
2G4674
KIT-VALVE & SEAL
14G, 16G, 621B, 637D, 641B, 651B, 651E, 657E, 769C
14G, 16G, 621B, 637D, 641B, 651B, 651E, 657E, 769C
1S1838
KIT
950, 966C, 988
950, 966C, 988
2V5372
KIT (Brake Shoe)
920, 950
920, 950
2S6613
KIT (GASKET)
613, 613B
613, 613B
3P8454
KIT (vent assem.)
12F, 12G, 14E, 14G, 16, 16G, 627, 627B, 631C, 637, 637D, 641B, 650B, 657B, 768C, 772, 777, 824C, 980C, 988B, 992, 992C, D8H
12F, 12G, 14E, 14G, 16, 16G, 627, 627B, 631C, 637, 637D, 641B, 650B, 657B, 768C, 772, 777, 824C, 980C, 988B, 992, 992C, D8H
3G1711
KIT (Seal)
637D
637D
2V9448
KIT
613, 910, 930, 950
613, 910, 930, 950
9J0628
KIT (front)
627B
627B
9J0629
KIT (rear)
627B
627B
1V4850
KIT
518, 528, 528B, 530B, 920, 930
518, 528, 528B, 530B, 920, 930
9J5114
KIT (Seal)
623B, 633C, 814, 815, 950
623B, 633C, 814, 815, 950