9J5111 KIT (seal) Caterpillar parts
140, 16, 191, 631C, 633C, 633D, 769, 941, 951B, 980B, 988
Rating:
Alternative (cross code) number:
CA9J5111
9J-5111
9J5111
CA9J5111
9J-5111
9J5111
Weight: 0.010 pounds 0 kg.
HYDRAULIC CONTROL, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 9J5111:
Information:
Use this procedure to troubleshoot a problem with the data link system. Also, use this procedure if one of the following diagnostic codes is active or easily repeated.
Table 1
J1939 Code and Description CDL Code and Description Comments
625–9
Proprietary Data Link : Abnormal Update Rate N/A N/A
639-9
J1939 Network #1 : Abnormal Update Rate 247-9
SAE J1939 Data Link : Abnormal Update Rate Communication has been lost to one or more of the devices on the datalink. If multiple devices are not communicating, there is likely a problem with the data link wiring, power, or ground circuits.
639-14
J1939 Network #1 : Special Instruction 247-14
SAE J1939 Data Link : Special Instruction The affected ECM is missing expected parameters.
1231-9
J1939 Network #2 : Abnormal Update Rate 2348-9
SAE J1939 Data Link #2 : Abnormal Update Rate Communication has been lost to one or more of the devices on the datalink. If multiple devices are not communicating, there is likely a problem with the data link wiring, power, or ground circuits.
Note: This code will log on the aftertreatment ECM if the Emergency Fuel Cutoff (EFCO) switch is used to shutdown the engine.
1231-14
J1939 Network #2 : Special Instruction 2348-14
SAE J1939 Data Link #2 : Special Instruction The affected ECM is missing expected parameters.
4193-9
Engine Coolant Pump Outlet Temperature : Abnormal Update Rate 2854-7
Coolant Temperature Control Module : Not Responding Properly N/A
4193-14
Engine Coolant Pump Outlet Temperature : Special Instruction 2349-14
Engine Coolant Pump Outlet Temperature Sensor : Special Instruction N/A
Table 2
Cat® ET Diagnostic Code Cross Reference to Wiring Schematic
Code Description Data Link
J1939 Network #1 Can A (Global)
J1939 Network #2 Can B (Local) Refer to the main engine Schematic, UENR7142 when troubleshooting the Data Link-Test.-9 Detected Problems:Device 1 is unable to communicate on the data link.
Device 1 cannot communicate with other Devices on the data link, but can communicate with the service tool, indicating a problem with the data link wiring.Device 1 is unable to communicate with Device 2 on the data link.
Device 1 cannot communicate with Device 2, indicating a problem with the data link wiring, power or ground circuit, or Device 2.-14 Detected Problems:Device 1 is unable to obtain a network address on the data link.
Device 1 is trying to claim the same address as another Device. An example of this is two Devices being configured the same.Device 1 detects a failed address claim from Device 2 on the data link.
Device 1 detects that Device 2 is trying to claim the same address as another Device.Device 1 is not receiving all expected parameters from Device 2 on the data link.
A component is configured as installed in the ECM, but is not installed on the application.
The incorrect component is installed.
The incorrect software file has been installed.
Illustration 1 g06320023
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the diagnostic code.
Codes
Result: A 4193-9 code is present.
Proceed to Test Step 11.
Result: A 4193-14 is present code.
Proceed to Test Step 3.
Result: A 639-9, 1235-9 639-9, 639-14
Table 1
J1939 Code and Description CDL Code and Description Comments
625–9
Proprietary Data Link : Abnormal Update Rate N/A N/A
639-9
J1939 Network #1 : Abnormal Update Rate 247-9
SAE J1939 Data Link : Abnormal Update Rate Communication has been lost to one or more of the devices on the datalink. If multiple devices are not communicating, there is likely a problem with the data link wiring, power, or ground circuits.
639-14
J1939 Network #1 : Special Instruction 247-14
SAE J1939 Data Link : Special Instruction The affected ECM is missing expected parameters.
1231-9
J1939 Network #2 : Abnormal Update Rate 2348-9
SAE J1939 Data Link #2 : Abnormal Update Rate Communication has been lost to one or more of the devices on the datalink. If multiple devices are not communicating, there is likely a problem with the data link wiring, power, or ground circuits.
Note: This code will log on the aftertreatment ECM if the Emergency Fuel Cutoff (EFCO) switch is used to shutdown the engine.
1231-14
J1939 Network #2 : Special Instruction 2348-14
SAE J1939 Data Link #2 : Special Instruction The affected ECM is missing expected parameters.
4193-9
Engine Coolant Pump Outlet Temperature : Abnormal Update Rate 2854-7
Coolant Temperature Control Module : Not Responding Properly N/A
4193-14
Engine Coolant Pump Outlet Temperature : Special Instruction 2349-14
Engine Coolant Pump Outlet Temperature Sensor : Special Instruction N/A
Table 2
Cat® ET Diagnostic Code Cross Reference to Wiring Schematic
Code Description Data Link
J1939 Network #1 Can A (Global)
J1939 Network #2 Can B (Local) Refer to the main engine Schematic, UENR7142 when troubleshooting the Data Link-Test.-9 Detected Problems:Device 1 is unable to communicate on the data link.
Device 1 cannot communicate with other Devices on the data link, but can communicate with the service tool, indicating a problem with the data link wiring.Device 1 is unable to communicate with Device 2 on the data link.
Device 1 cannot communicate with Device 2, indicating a problem with the data link wiring, power or ground circuit, or Device 2.-14 Detected Problems:Device 1 is unable to obtain a network address on the data link.
Device 1 is trying to claim the same address as another Device. An example of this is two Devices being configured the same.Device 1 detects a failed address claim from Device 2 on the data link.
Device 1 detects that Device 2 is trying to claim the same address as another Device.Device 1 is not receiving all expected parameters from Device 2 on the data link.
A component is configured as installed in the ECM, but is not installed on the application.
The incorrect component is installed.
The incorrect software file has been installed.
Illustration 1 g06320023
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the diagnostic code.
Codes
Result: A 4193-9 code is present.
Proceed to Test Step 11.
Result: A 4193-14 is present code.
Proceed to Test Step 3.
Result: A 639-9, 1235-9 639-9, 639-14
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
9J5112
KIT (seal)
16, 173B, 528, 613B, 621, 650B, 920
16, 173B, 528, 613B, 621, 650B, 920
9J5108
KIT (seal)
621, 621B, 623, 623B, 627B, 633D, 641B, 772, 966C, 983, 992
621, 621B, 623, 623B, 627B, 633D, 641B, 772, 966C, 983, 992
2G7182
KIT-CARTRIDGE
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
2G7183
KIT-REFILL
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
2G7184
KIT-PURGE VALVE
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
611, 615, 615C, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, 69D, 768C, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776, 776C, 776D, ...
7K9680
KIT-BRAKE ACTUATOR
120G, 12G, 14G, 16G, 528, 528B, 530B, 613C, 613C II, 621, 621B, 621E, 627E, 772, 814, 814B, 815B, 824C, 826C, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 966C, 966D, 966F, 966F II, 966R, 970F, 980...
120G, 12G, 14G, 16G, 528, 528B, 530B, 613C, 613C II, 621, 621B, 621E, 627E, 772, 814, 814B, 815B, 824C, 826C, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 966C, 966D, 966F, 966F II, 966R, 970F, 980...
5J0102
KIT (Seal)
623, 623B, 633C, 814, 814S, 950
623, 623B, 633C, 814, 814S, 950
9J5106
KIT (Seal)
631C, 633D, 641, 641B, 824B, 988
631C, 633D, 641, 641B, 824B, 988
9J5114
KIT (Seal)
623B, 633C, 814, 815, 950
623B, 633C, 814, 815, 950
4J8494
KIT (Cartridge)
769, 950
769, 950
1S1838
KIT
950, 966C, 988
950, 966C, 988
9J5116
KIT (seal)
153, 518, 941, D4E
153, 518, 941, D4E
5C1185
KIT (slide rail assem.)
920, 966C, D4D
920, 966C, D4D
2P0895
KIT (SERVICE)
571G, 572G, D7F, D7G
571G, 572G, D7F, D7G
9J5112
KIT (seal)
16, 173B, 528, 613B, 621, 650B, 920
16, 173B, 528, 613B, 621, 650B, 920