9J5114 KIT (Seal) Caterpillar parts
623B, 633C, 814, 815, 950
Rating:
Alternative (cross code) number:
CA9J5114
9J-5114
9J5114
CA9J5114
9J-5114
9J5114
Weight: 0.15 pounds 0 kg.
SOIL COMPACTOR, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 9J5114:
Information:
Remove Flywheel Housing
Start By:a. remove all turbochargersb. remove crankshaft rear seal and wear sleeve 1. Disconnect connector (1). 2. Attach Tool (A) and fasten a hoist.3. Remove four bolts (3) and stack (2). The weight of the stack and hardware is 45 kg (100 lb). 4. Remove hose clamp (6).5. Remove five bolts (5) and support (4).6. Repeat Steps 4 and 5 for the other side of the engine. 7. Remove six bolts (7) that connect oil pan (8) to flywheel housing (9). Loosen the rest of the bolts that hold the oil pan in position. 8. Attach Tool (A) to the flywheel housing and a hoist. 9. Lift the end of the engine enough so a 1/2 " Hardened Washer (10) can be installed on each side of the engine between the oil pan and the cylinder block.10. Install blocks under the oil pan to support the engine when the flywheel housing is removed. Lower the engine onto the blocks. 11. Remove twenty one bolts (11) and flywheel housing (9). The weight of the flywheel housing is 91 kg (200 lb).Install Flywheel Housing
1. Install two 1/2 " - 13 NC × 4" Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (200 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts:a. Tighten bolts 1 through 8 in number sequence to 136 14 N m (100 10 lb ft).b. Tighten bolts 9 through 17 (3408) and 9 through 20 (3412) in number sequence to 55 7 N m (41 5 lb ft).c. Again, tighten bolts 1 through 8 in number sequence to 136 14 N m (100 10 lb ft).d. Again, tighten bolts 9 through 20 in number sequence to 55 7 N m (41 5 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8.
Start By:a. remove all turbochargersb. remove crankshaft rear seal and wear sleeve 1. Disconnect connector (1). 2. Attach Tool (A) and fasten a hoist.3. Remove four bolts (3) and stack (2). The weight of the stack and hardware is 45 kg (100 lb). 4. Remove hose clamp (6).5. Remove five bolts (5) and support (4).6. Repeat Steps 4 and 5 for the other side of the engine. 7. Remove six bolts (7) that connect oil pan (8) to flywheel housing (9). Loosen the rest of the bolts that hold the oil pan in position. 8. Attach Tool (A) to the flywheel housing and a hoist. 9. Lift the end of the engine enough so a 1/2 " Hardened Washer (10) can be installed on each side of the engine between the oil pan and the cylinder block.10. Install blocks under the oil pan to support the engine when the flywheel housing is removed. Lower the engine onto the blocks. 11. Remove twenty one bolts (11) and flywheel housing (9). The weight of the flywheel housing is 91 kg (200 lb).Install Flywheel Housing
1. Install two 1/2 " - 13 NC × 4" Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (200 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts:a. Tighten bolts 1 through 8 in number sequence to 136 14 N m (100 10 lb ft).b. Tighten bolts 9 through 17 (3408) and 9 through 20 (3412) in number sequence to 55 7 N m (41 5 lb ft).c. Again, tighten bolts 1 through 8 in number sequence to 136 14 N m (100 10 lb ft).d. Again, tighten bolts 9 through 20 in number sequence to 55 7 N m (41 5 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8.
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
5J1251
KIT (Cartridge)
950, 955K
950, 955K
2G6664
KIT-DIAPHRAGM
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 5130, ...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 5130, ...
7K9680
KIT-BRAKE ACTUATOR
120G, 12G, 14G, 16G, 528, 528B, 530B, 613C, 613C II, 621, 621B, 621E, 627E, 772, 814, 814B, 815B, 824C, 826C, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 966C, 966D, 966F, 966F II, 966R, 970F, 980...
120G, 12G, 14G, 16G, 528, 528B, 530B, 613C, 613C II, 621, 621B, 621E, 627E, 772, 814, 814B, 815B, 824C, 826C, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 966C, 966D, 966F, 966F II, 966R, 970F, 980...
4V4972
KIT-HYDRAULIC BRAKE
518, 528, 528B, 530B, 613C, 613C II, 916, 950, 950B, 950B/950E, G936
518, 528, 528B, 530B, 613C, 613C II, 916, 950, 950B, 950B/950E, G936
4V5415
KIT-CYLINDER
528, 528B, 530B, 613C, 613C II, 926, 930, 930R, 950, 950B, 950B/950E, D300B, G936
528, 528B, 530B, 613C, 613C II, 926, 930, 930R, 950, 950B, 950B/950E, D300B, G936
5J0102
KIT (Seal)
623, 623B, 633C, 814, 814S, 950
623, 623B, 633C, 814, 814S, 950
1V2119
KIT (Caliper)
613, 930, 950
613, 930, 950
2V9448
KIT
613, 910, 930, 950
613, 910, 930, 950
3Y3484
KIT-REPAIR
920, 950
920, 950
4J8494
KIT (Cartridge)
769, 950
769, 950
1S1838
KIT
950, 966C, 988
950, 966C, 988
9J5106
KIT (Seal)
631C, 633D, 641, 641B, 824B, 988
631C, 633D, 641, 641B, 824B, 988
2V5372
KIT (Brake Shoe)
920, 950
920, 950
2S6613
KIT (GASKET)
613, 613B
613, 613B
3P8454
KIT (vent assem.)
12F, 12G, 14E, 14G, 16, 16G, 627, 627B, 631C, 637, 637D, 641B, 650B, 657B, 768C, 772, 777, 824C, 980C, 988B, 992, 992C, D8H
12F, 12G, 14E, 14G, 16, 16G, 627, 627B, 631C, 637, 637D, 641B, 650B, 657B, 768C, 772, 777, 824C, 980C, 988B, 992, 992C, D8H
9J5507
KIT (seal)
508, 910
508, 910
3G1711
KIT (Seal)
637D
637D
2V9448
KIT
613, 910, 930, 950
613, 910, 930, 950
9J0628
KIT (front)
627B
627B
9J0629
KIT (rear)
627B
627B
1V4850
KIT
518, 528, 528B, 530B, 920, 930
518, 528, 528B, 530B, 920, 930