2D4215 KNUCKLE (R H) Caterpillar parts
120, 12E
Rating:
Alternative (cross code) number:
CA2D4215
2D-4215
2D4215
CA2D4215
2D-4215
2D4215
Weight: 19 pounds 8 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$375.00
21 Jun 2022
US: Florida-Parts-Z
2D4215 - Knuckle (R.H.) fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$337.07
29 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Knuckle 2D4215 New
$357.70
31 May 2017
19.64[8.55] pounds
CTP: CTP
Caterpillar KNUCKLE (2D4215)
2D4215<br> Caterpillar<br> Weight(lbs): 19.60 <br>Length(cm): 36.0000 <br>Width(cm): 32.0000 <br>Depth(cm): 12.0000 <br>||
2D4215<br> Caterpillar<br> Weight(lbs): 19.60 <br>Length(cm): 36.0000 <br>Width(cm): 32.0000 <br>Depth(cm): 12.0000 <br>||
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 390-1131 Crankshaft Locking Pin 1
B - Balancer Timing Pin
(Bolt M8 by 22mm) 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure. Note: In order to remove the balancer safely, the engine must be removed from the machine. The engine should be mounted in a suitable stand and placed in the inverted position.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02887016
Illustration 2 g02709625
Illustration 3 g02893017
Remove plug (2) from Position (X) in the cylinder block. Remove O-ring seal (1) from the plug.
Install Tooling (A) into the cylinder block in Position (X). Note: Tooling (A) must be located in Position (Y) in the crankshaft.Note: Ensure that Tooling (A) is located in the correct drilling in the crankshaft as shown in Illustration 1.
Remove bolts (6) from oil suction pipe (3).
Remove bolt (7) from oil suction pipe (3).
Remove oil suction pipe (3) from the cylinder block. Remove O-ring seal (8) from the oil suction pipe.
Movement of the counterweight can cause personal injury.
Install Tooling (B) in Position (Z) in order to prevent movement of the counterweights. Note: If Tooling (B) cannot be installed to the balancer, the crankshaft is not in the correct position.
Attach a suitable lifting device to balancer (4). Support the weight of balancer, the weight is approximately 15 kg (33 lb).
Use the suitable lifting device in order to remove the balancer from the cylinder block.
Do not remove dowels (9) unless the dowels are damaged.
Table 1
Required Tools
Tool Part Number Part Name Qty
A 390-1131 Crankshaft Locking Pin 1
B - Balancer Timing Pin
(Bolt M8 by 22mm) 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure. Note: In order to remove the balancer safely, the engine must be removed from the machine. The engine should be mounted in a suitable stand and placed in the inverted position.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02887016
Illustration 2 g02709625
Illustration 3 g02893017
Remove plug (2) from Position (X) in the cylinder block. Remove O-ring seal (1) from the plug.
Install Tooling (A) into the cylinder block in Position (X). Note: Tooling (A) must be located in Position (Y) in the crankshaft.Note: Ensure that Tooling (A) is located in the correct drilling in the crankshaft as shown in Illustration 1.
Remove bolts (6) from oil suction pipe (3).
Remove bolt (7) from oil suction pipe (3).
Remove oil suction pipe (3) from the cylinder block. Remove O-ring seal (8) from the oil suction pipe.
Movement of the counterweight can cause personal injury.
Install Tooling (B) in Position (Z) in order to prevent movement of the counterweights. Note: If Tooling (B) cannot be installed to the balancer, the crankshaft is not in the correct position.
Attach a suitable lifting device to balancer (4). Support the weight of balancer, the weight is approximately 15 kg (33 lb).
Use the suitable lifting device in order to remove the balancer from the cylinder block.
Do not remove dowels (9) unless the dowels are damaged.
Caterpillar parts catalog:
Parts knuckle Caterpillar catalog:
120, 12E
120, 12E
0777743
KNUCKLE AS
SS-250
SS-250
RM-350B
1591138
KNUCKLE
RM-350B
RM-350B
1328023
KNUCKLE
RM-250C, RR-250B
RM-250C, RR-250B
1G2191
KNUCKLE AS-RH
120B
120B
1G2192
KNUCKLE AS
120B
120B
140, 140B
140, 140B