LADDER GP 9C9213 - Caterpillar

Image1.8.1
Illustration 1.8.1. The interior side of the cushion hitch valve showing location of new clip.
On the inboard side of the cushion hitch valve, install a new 130-5300 Clip (14), using the existing bolt and washer for the hydraulic hose split flange. This clip will hold the connector for the cushion hitch solenoid and the new harness assembly.
Image1.9.1
Illustration 1.9.1. Shows the rear of the cushion hitch valve.
Install the 2W-7940 Bracket (1) to the rear of the cushion hitch valve mounting bracket, along with the 130-5300 Clip (D), the 4P-7581 Ladder Clip (C), 4L-6454 Bolt (4), and 8T-4896 Washer (F). The 130-5300 Clip, 4P-7581 Ladder Clip, and the 8T-4896 Washer are components that were retained from disassembly. Install the 130-5300 Clip (D) with the clip towards the cushion hitch mounting bracket. This clip will hold the auger filter connector. Install the 4P-7581 Ladder Clip with the angle away from the 130-5300 Clip. Once the clips are installed, the new 328-8946 Cushion Hitch Harness Assembly (16) will be zip tied to the 4P-7581 Ladder Clip using one 3S-2093 Cable Strap.
At the top of the newly installed 2W-7940 Bracket (1), install one 5P-9297 Clip (7), one 5S-7379 Bolt (8), two 8T-4896 Washers (13), and one 6V-8801 nut (9). Use a washer on each side of the bracket, one for the bolt, and one for the washer.
At the bottom of the cushion hitch valve mounting bracket, on the boss, attach the harness using one 8M-2773 Clip (11), one 5S-7379 Bolt (E), and one 8T-4896 Washer (F). The 5S-7379 Bolt and 8T-4896 Washer were retained from disassembly. After the new harness is clipped, zip tie the arc suppressor connector back to the main harness bundle using one 3S-2093 Cable Strap (2).
Image1.10.1
Illustration 1.10.1 shows the area of hardware installation along the right hand side of the hitch.
Image1.11.1
Illustration 1.11.1 shows the clip locations along the right hand side of the hitch.
Along the right hand side of the hitch, in front of the lower cushion hitch H-link, install one 8M-2773 Clip (G) using the bolt and washer from the cushion clamp bracket.
Below the lower cushion hitch H-link, install one 4K-8302 Clip (3), using the bolt and washer for the hard line support bracket.
Be sure that the new harness is clipped at the green tape locations. These are the optimum clipping points for the harness to ensure sufficient slack at the hitch joint. The green tape location is shown above the upper clip in illustration 1.11.1 for visual purposes.
Image1.12.1
Illustration 1.12.1 shows the final clipping point at the rear of the hitch on top of the case.
Image1.13.1
Illustration 1.13.1 shows the clipping point at the top of the case.
On top of the case, at the rear horizontal hitch pin saddle, attach to the boss one 4S-1962 Clip (6), one 7V-6571 Grommet (10), one 132-7551 Spacer (15), one 8T-2502 Bolt (12), and one 8T-4896 Washer (F). The 8T-4896 Washer was retained from disassembly. This clip should be oriented with the barrel approximately 45 degrees above horizontal, and the clip should be