AVSPARE.COM
parts catalog

Lafayette 3616 Engine BAV3100 - Caterpillar



BAV3100 Lafayette 3616 Engine Caterpillar parts 3616 Lafayette
Rating:
43
Alternative (cross code) number:
CABAV3100
BAV-3100
BAV3100
Caterpillar BAV3100 Lafayette 3616 Engine

Buy Lafayette 3616 Engine BAV3100 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: BAV3100:

MARINE ENGINE  3616   Caterpillar
  For full view, you need register

Information:


Illustration 8 g01347216
While the loader arms are fully lowered, visually inspect the quick coupler in order to ensure that the coupler pins (4) are fully extended through the corresponding holes (4A) of the frame mounting bracket. Verify that the coupler pins (4) are engaged before you operate the host machine with the work tool.
Illustration 9 g03685615
Raise the storage stands and secure the stands with the pin.
Use the following procedure to verify engagement of the coupler pins.
Enter the machine.
Close the cab door.
Fasten the seat belt.
Lower the armrest, if equipped.
Start the engine.
Disengage the parking brake.
Keep the work tool close to the ground.
Activate the tilt control in order to tilt the work tool downward.
Put downward pressure on the work tool until tension is loosened on the angle adjustment chains.
Move the machine backward. Ensure that there is no movement between the work tool and the quick coupler assembly.
Test the work tool for proper operation.
Engage the parking brake and stop the engine.
Exit the machine.
Inspect the work tool and the auxiliary hydraulic lines for leaks. Inspect the work tool for wear, for damage and for proper adjustment. Refer to Operation and Maintenance Manual, "Broom - Inspect/Adjust/Replace" for additional information.Removing the Work Tool
Disengaging the coupler pins will release the work tool from control of the operator.Serious injury or death may result from disengaging the work tool when the work tool is in an unstable position or carrying a load.Place the work tool in a stable position before disengaging the coupler pins.
Auxiliary hoses for work tools must be disconnected before the Hydraulic Quick Coupler is disengaged.Pulling the work tool with the auxiliary hoses could result in damage to the host machine or the work tool.
Enter the host machine.
Fasten the seat belt.
Lower the armrest, if equipped.
Start the engine.
Disengage the parking brake.
Raise the work tool in the transport position. Move the host machine to the desired location for disconnecting the work tool. Refer to Operation and Maintenance Manual, "Transportation" for additional information on transporting the work tool.
Position the host machine on a level surface.
Rack back the work tool until the work tool is slightly off the ground.
Place the direction control in NEUTRAL. Engage the parking brake.
Turn the engine start switch key to the OFF position in order to stop the engine.
Follow the procedure in the Operation and Maintenance Manual of the host machine to relieve any pressure within the auxiliary hydraulic lines. For Caterpillar Skid Steer Loaders and Compact Wheel Loaders, use the following procedure.
Turn the engine start switch to the ON position. Do not start the engine.
Disengage the parking brake.
Operate the auxiliary hydraulic control back and forth and press the control buttons for several times in order to relieve hydraulic pressure within the auxiliary hydraulic lines.
Engage the parking brake and turn the engine start switch to the OFF position.
Exit the machine.
Disconnect the auxiliary hydraulic lines from the host machine.
Disconnect the wire harness from the host machine, if equipped.
If protective caps are available, install protective caps over the quick connect couplers.This will help avoid dirt from entering the quick connect

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.