BBHML00 Lafayette 3612 Engine Caterpillar parts
3612
Rating:
Alternative (cross code) number:
CABBHML00
BBH-ML00
BBHML00
CABBHML00
BBH-ML00
BBHML00
MARINE ENGINE,
Compatible equipment models: BBHML00:
For full view, you need register
Information:
Specification
Table 1
Approximate Change of Flow with 1/4 Turn of Adjustment Screw
Adjustment Screw 1/4 Turn of Adjustment Screw Torque for Locknut
Flow Control 19 L/min (5.0 US gpm) 22 2 N m (16 1.5 lb ft)
Maximum Output Flow 3.4 L/min (0.9 US gpm) 72 7 N m (53 5 lb ft) Introduction
Adjust the pump output flow if the flow test results differ greatly from the specifications and the test results were reviewed by your regional product support team through the Dealer Solutions Network..Adjustment of Pump Output Flow (Flow Control)
Illustration 1 g06223349
Pump regulators and adjustment screws
(1) Pump 1 regulator
(2) Pump 1 regulator locknut
(3) Pump 1 regulator adjustment screw
(4) Pump 2 regulator
(5) Pump 2 regulator locknut
(6) Pump 2 regulator adjustment screwAdjust the flow of pump 1 for the flow control. Pump 2 must be at no-load condition.
Loosen locknut (2).
Turn adjustment screw (3) to adjust the output flow of the pump. Turning adjustment screw (3) clockwise will increase the output flow of the pump. Turning adjustment screw (3) counterclockwise will decrease the output flow of the pump. A 1/4 turn of adjustment screw (3) will change the output flow of the pump at the following pressure.
Output flow of the pump will change approximately 19 L/min (5.0 US gpm) if the output flow is adjusted at 5000 kPa (725 psi) at 1650 rpm.
Tighten locknut (2) to a torque of 22 2 N m (16 1.5 lb ft).Adjust pump 2 in the same manner as pump 1.Adjustment of the Maximum Output Flow of the Pump
Illustration 2 g06223382
Pump adjustment screws
(7) Pump 1 locknut
(8) Pump 1 adjustment screw
(9) Pump 2 locknut
(10) Pump 2 adjustment screwAdjust the maximum output flow of pump 1.
Loosen locknut (7).
To adjust maximum output flow, turn adjustment screw (8). Turning adjustment screw (8) clockwise will decrease the maximum output flow of the pump. Turning adjustment screw (8) counterclockwise will increase the maximum output flow of the pump. A 1/4 turn of adjustment screw (8) will change the maximum output flow approximately 3.4 L/min (0.9 US gpm).
Tighten locknut (7) to a torque of 72 7 N m (53 5 lb ft).Adjust the maximum output flow of pump 2 in the same manner as pump 1.
Table 1
Approximate Change of Flow with 1/4 Turn of Adjustment Screw
Adjustment Screw 1/4 Turn of Adjustment Screw Torque for Locknut
Flow Control 19 L/min (5.0 US gpm) 22 2 N m (16 1.5 lb ft)
Maximum Output Flow 3.4 L/min (0.9 US gpm) 72 7 N m (53 5 lb ft) Introduction
Adjust the pump output flow if the flow test results differ greatly from the specifications and the test results were reviewed by your regional product support team through the Dealer Solutions Network..Adjustment of Pump Output Flow (Flow Control)
Illustration 1 g06223349
Pump regulators and adjustment screws
(1) Pump 1 regulator
(2) Pump 1 regulator locknut
(3) Pump 1 regulator adjustment screw
(4) Pump 2 regulator
(5) Pump 2 regulator locknut
(6) Pump 2 regulator adjustment screwAdjust the flow of pump 1 for the flow control. Pump 2 must be at no-load condition.
Loosen locknut (2).
Turn adjustment screw (3) to adjust the output flow of the pump. Turning adjustment screw (3) clockwise will increase the output flow of the pump. Turning adjustment screw (3) counterclockwise will decrease the output flow of the pump. A 1/4 turn of adjustment screw (3) will change the output flow of the pump at the following pressure.
Output flow of the pump will change approximately 19 L/min (5.0 US gpm) if the output flow is adjusted at 5000 kPa (725 psi) at 1650 rpm.
Tighten locknut (2) to a torque of 22 2 N m (16 1.5 lb ft).Adjust pump 2 in the same manner as pump 1.Adjustment of the Maximum Output Flow of the Pump
Illustration 2 g06223382
Pump adjustment screws
(7) Pump 1 locknut
(8) Pump 1 adjustment screw
(9) Pump 2 locknut
(10) Pump 2 adjustment screwAdjust the maximum output flow of pump 1.
Loosen locknut (7).
To adjust maximum output flow, turn adjustment screw (8). Turning adjustment screw (8) clockwise will decrease the maximum output flow of the pump. Turning adjustment screw (8) counterclockwise will increase the maximum output flow of the pump. A 1/4 turn of adjustment screw (8) will change the maximum output flow approximately 3.4 L/min (0.9 US gpm).
Tighten locknut (7) to a torque of 72 7 N m (53 5 lb ft).Adjust the maximum output flow of pump 2 in the same manner as pump 1.