AVSPARE.COM
parts catalog

Lafayette 3606 Engine BBNDK00 - Caterpillar



BBNDK00 Lafayette 3606 Engine Caterpillar parts G3606B Lafayette
Rating:
21
Alternative (cross code) number:
CABBNDK00
BBN-DK00
BBNDK00
Caterpillar BBNDK00 Lafayette 3606 Engine

Buy Lafayette 3606 Engine BBNDK00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BBNDK00:

GAS ENGINE  G3606B   Caterpillar
  For full view, you need register

Information:


Illustration 1 g06228867
Operator console
(1) Engine deceleration lever
(2) Service brake lever
(3) Status display
(4) Implement select switch
(5) High-idle engine speed select dial
(6) Blade float select / winch free spool button
(7) Auto blade assist mode select / winch option slow mode button
(8) Blade pitch / ripper / winch control knob
(9) Implements control
(10) Implement lockout switch
(11) Machine power / engine crank switch
(12) Parking brake switch
(13) Steering / direction control
(14) Gear shift up / down knob
(15) Avoidance zone LED (not used)
(16) Parking brake LED
(17) Software stop LED
(18) Fire suppression switch (if equipped)
(19) Active fault LED
(20) Implement lockout LED
(21) Battery / wireless status LED
Illustration 2 g06229164
Left side of operator console
(22) Engine high / low idle button
(23) Display select button
Illustration 3 g06229168
Right side of operator console
(24) Operator console power button
(25) Horn button
(26) Operator console commanded stop switch
(27) Not used this machine series
(28) Machine work light button
(29) RFID chip slot
Confirm that the Operator Console Commanded Stop (26) is turned off, turn the switch clockwise to disengage.
Turn the following switches to the default position.
"Implement Lockout" (10) ON
"Parking Brake" (12) ON
"Machine Power/Engine Crank" (11) OFF
"Implements Control" (9) CENTER
"Steering / Direction Control" (13) CENTER
Make sure that the operator console is upright.Note: The operator console has a built-in inclinometer / accelerometer sensor which prevents operation when the console is tilted past 45 degrees in any direction or is dropped.
Press the Operator Console Power button (24) to power on the operator console.
Illustration 4 g06246621
Operator console access card scan area
(30) Front-right corner
Within 8 seconds, scan the Operator Console Access Card on the front-right corner of the Operator Console where the indicator label is. A dim Cat logo will appear until the Operator Console Access Card is swiped. The Cat logo will appear brighter when the card is successfully swiped.Note: If the Operator Console Access Card is not scanned within 8 seconds, the Operator Console will power off, and the procedure will require repeated.
Place the Machine Power / Engine Crank switch (11) on the operator console to the ON (center) position.Note: For this test procedure there is no need to sound the horn to activate RC or start the machine engine.
Press the "Engine Shutdown Switch" (34) on the "GLSC".Note: After performing this step, the action alarm on the console should activate. The "Active Fault LED" (19) should flash "RED" with every sound of the action alarm.Note: Along with the action alarm sounding the EID 678, "Ground Level Shutdown Event", code will be raised.
Reset the "Engine Shutdown Switch" (34) on the "GLSC" by pulling out the switch.Note: Operator Console check is now complete.Refer to the Operation and Maintenance Manual, M0085769, "Preliminary Remote Console Checks" section within this manual for additional information to continue to activate RC.

Caterpillar SIS machinery equipment:



Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.