AVSPARE.COM
parts catalog

Lafayette 3606 Engine BBSNZ00 - Caterpillar



BBSNZ00 Lafayette 3606 Engine Caterpillar parts G3606B Lafayette
Rating:
33
Alternative (cross code) number:
CABBSNZ00
BBS-NZ00
BBSNZ00
Caterpillar BBSNZ00 Lafayette 3606 Engine

Buy Lafayette 3606 Engine BBSNZ00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BBSNZ00:

GAS ENGINE  G3606B   Caterpillar
  For full view, you need register

Information:

Note: Caterpillar recommends using Caterpillar service tools or service tools with equivalent specifications.Failure to heed this warning can lead to premature failures, product damage, personal injury or death.
Illustration 1 g06262220
MP332 Speed control valve
(1) Main pressure relief valveFactory setting for main pressure relief valve (1), booster pressure, is 72000 2000 kPa (10440 290 psi).The jaw set must be removed first to get access to the hydraulic test ports.System Check - Main Relief Valve Pressure
Remove the jaw set from the Multi-Processor frame. Refer to Operation and Maintenance Manual, "Changing the Jaw Sets" for the proper procedure.
Lower the Multi-Processor to the ground and stop the engine of the host machine. Relieve the pressure from the hydraulic system. Refer to the Service Manual for the host machine for the proper procedure.
Illustration 2 g06262151
Test port location of MP332
(2) Plate
Remove plate (2) (if equipped) to gain access to the test ports.Note: Tilt the hydraulic cylinder towards the rotator to gain better access. Secure against tilting by using the cylinder blocking pipe. Refer to Operations and Maintenance Manual, "Changing the Jaw Sets", for the proper procedure.
Illustration 3 g06262162
MP332 test ports
(3) Test port "MB"
(4) Test port "MBZ"
Remove plugs from test port "MB" (3) and test port "MBZ" (4) .
Install tooling (A5) onto test port "MBZ" (4).
Install tooling (A2) onto test port "MB" (3).
Illustration 4 g06262132
MP332
Install tooling (A7) onto tooling (A5).
Install tooling (A8) onto tooling (A2).
Install tooling (A9) onto tooling (A7).
Install tooling (A9) onto tooling (A8).
Install tooling (A9) onto tooling (A6).
Activate tooling (A6).Note: Read Operator Manual tooling (A6) for correct procedures.
Start the engine of the host machine and operate the host machine until the hydraulic oil reaches normal operating temperature.
Extend cylinder rod until cylinder rod is fully extended (at stop).Note: This action is needed to activate booster mode.
Measure pressure at test port "MBZ" (4). Pressure value must not exceed 74000 kPa (10735 psi) when the host machine pressure at test port "MB" (3) is at the minimum value of 33000 kPa (4790 psi).Note: Pressure at test port "MB" (3) is equal to the host machine pressure.Note: When the host machine pressure at test port "MB" (3) is below the minimum, 33000 kPa (4790 psi), the 74000 kPa (10735 psi) at test port "MBZ" (4) will not be reached.
Adjust main pressure relief valve (1) when pressure at test port "MBZ" (4) is below 70000 kPa (10150 psi) and host machine pressure at test port "MB" (3) is minimum 33000 kPa (4790 psi). Refer to"Adjustment - Main Relief Valve Pressure" for more information. Go to Step 4 in"Adjustment - Main Relief Valve Pressure" when the pressure setting is within specifications, 72000 2000 kPa (10450 290 psi).Adjustment - Main Relief Valve Pressure
Illustration 5 g06262224
MP332 Speed control valve
(1) Main pressure relief valve
(5) Locknut
(6) Screw
(7) Cap
Remove cap (7) from main pressure relief valve (1).
Loosen locknut (5) and turn screw (6) clockwise to raise the pressure at test port "MBZ" (4).Note: 1/8 turn is approximately 2000 kPa (290 psi).
Retract cylinder rod partly.Note: This action will deactivate booster mode.
Tighten locknut (5) to 30 3

Caterpillar SIS machinery equipment:



Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.