AVSPARE.COM
parts catalog

Lafayette 3616 Engine BCL4900 - Caterpillar



BCL4900 Lafayette 3616 Engine Caterpillar parts G3616 Lafayette
Rating:
18
Alternative (cross code) number:
CABCL4900
BCL-4900
BCL4900
Caterpillar BCL4900 Lafayette 3616 Engine

Buy Lafayette 3616 Engine BCL4900 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BCL4900:

GAS ENGINE  G3616   Caterpillar
  For full view, you need register

Information:

Chassis ECM
The following is a list of Diagnostic Trouble Codes (DTCs) that are associated with the configuration parameters of the ECM.
Table 1
Chassis ECM
DTC Description System Response
268-2 Programmed Parameter Fault: Data Erratic, Intermittent, or Incorrect The ECM has determined that a configuration parameter is not programmed. The ECM will display the parameter causing the problem on the Cat® Electronic Technician (CatET) Service Tool. The programming parameters identify conditions related to the programming of the ECM or a signal failure. A failure of the internal program of the ECM is associated with this diagnostic code as well. The fault messages displayed in Cat® Electronic Technician (CatET) Service Tool or via the operator monitor include "programmed parameter fault" or other machine monitoring failures.Possible causes for an FMI 2 diagnostic code are:
The sales model and product identification are not programmed into the ECM.
The ECM is incorrect.Note: The correct sales model and product identification must be programmed when new software is flashed to the ECM.All the attachments for the machine are configured in the ECM. The ECM activates the 268-2 diagnostic code when an attachment is configured incorrectly.Diagnostic Trouble Code Procedure
Identify the active FMI code associated with the components.
Determine which code is present and use the list below to determine which procedure to follow.
FMI 2 diagnostic code, proceed to Table 2.
Table 2
FMI 2 Troubleshooting
Troubleshooting Test Steps Values Results
1. Verify The Configuration Of The Sales Model.
A. Use the Cat® Electronic Technician (Cat ET) Service Tool to verify that the ECM is configured to the default setting configuration.
The ECM has been configured correctly to the default setting configuration. OK - The ECM has been configured correctly to the default setting configuration.
Verify that the new configuration has corrected the problem before attempting to operate the machine.
Proceed to Test Step 3.
NOT OK - The ECM does not have the appropriate sales model and product identification.
Proceed to Test Step 2.
2. Configure The ECM.
A. Use Cat ET to reset the configuration to the default setting configuration. Enter the correct information for sales model and product identification.
B. Reset the installation status to the correct type for the attachments that are installed on the machine.
The ECM is configured to the default setting configuration. OK - The ECM is configured to the default setting configuration.
Verify that the new configuration has corrected the problem before attempting to operate the machine.
Proceed to Test Step 3.
NOT OK - The ECM is not configured to the default setting configuration.
Repair: Repeat this procedure.
If the diagnostic code remains active or repeatedly activated and no cause can be found, flash the ECM with the latest software version. Ensure that you have the latest software version for your specific machine and ECM. Refer to the Troubleshooting, "ECM Software - Install" section of this manual for the correct procedure.
If the problem is still present after flashing the latest software to the ECM, contact the Technical Communicator at your dealership for a possible consultation with Caterpillar.
Proceed to Test Step 3.
3. Check If The Diagnostic Code Remains
A. Turn the key start switch and

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.