AVSPARE.COM
parts catalog

Lafayette 3608 Engine BFFWT00 - Caterpillar



BFFWT00 Lafayette 3608 Engine Caterpillar parts 3608 Lafayette
Rating:
60
Alternative (cross code) number:
CABFFWT00
BFF-WT00
BFFWT00
Caterpillar BFFWT00 Lafayette 3608 Engine

Buy Lafayette 3608 Engine BFFWT00 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE AUXILIARY,

Compatible equipment models: BFFWT00:

MARINE AUXILIARY  3608   Caterpillar
  For full view, you need register

Information:

Machine ECM 1
The following is a list of Diagnostic Trouble Codes (DTCs) associated with the bluetooth transceiver of the machine.
Table 1
Machine ECM 1 (MID 299)
DTC Code Description System Response
5874-9 Bluetooth Transceiver: Abnormal Update Rate Operator can not authenticate using bluetooth key or phone app. Each CAN data link circuit is an input and output of select electronic control modules. The data link is designed to carry communications between the electronic control modules.Possible Causes for an FMI 9 Diagnostic code are:
CAN harness wiring failure.
Connector failure.
Transceiver failure.Note: A loss of power in the system to an ECM can cause the ECM to activate this diagnostic code combination. Ensure that ECM modules with this diagnostic code are powered up before proceeding with this procedure.The FMI 9 code means that the ECM has lost all communication with another control module.The preceding diagram is a simplified schematic of the data link connections. The schematic is electrically correct. However, not all the possible harness connectors are shown. Refer to the latest revision of the Electrical Schematic to view the entire circuitry of the machine.Diagnostic Trouble Code Procedure
Prior to beginning this procedure, inspect the harness connectors involved in this circuit. Poor connections are often the cause of problems in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring for pinch points or abrasions. Look for and repair areas where wires are exposed. If a problem with a connection is found, correct the problem. Verify that this diagnostic code is active before performing a troubleshooting procedure.
Identify the active FMI code associated with the components.
Determine which code is present and use the list below to determine which procedure to follow.
FMI 9 Diagnostic code, proceed to Table 2.
Table 2
FMI 9 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check if the transceiver is installed. (1)
Transceiver is installed. OK - Transceiver is installed.
Proceed to Test Step 3.
NOT OK - Transceiver not installed.
Proceed to Test Step 2.
2. Set "Operator Management Bluetooth Device Enable Status" configuration to disabled.
OK -
Proceed to Test Step 3.
3. Verify transceiver is powered.
OK - Transceiver has power.
Proceed to Test Step 4.
4. Complete CAN wiring troubleshooting between transceiver and connection to CAN bus. Refer to Troubleshooting, "Can Data Link - Test". OK -
STOP.
NOT OK -
Proceed to Test Step 5
5. Replace transceiver module. OK -
STOP.
NOT OK -.
Prior to replacing the transceiver, always contact the Technical Communicator at your dealership for possible consultation with Caterpillar. This consultation may effect repair time.
STOP.
(1) Consult your Caterpillar Authorized Dealer for the correct part numbers of the flash software.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.