AVSPARE.COM
parts catalog

Lafayette 3606 Engine BFNDX00 - Caterpillar



BFNDX00 Lafayette 3606 Engine Caterpillar parts G3606B Lafayette
Rating:
24
Alternative (cross code) number:
CABFNDX00
BFN-DX00
BFNDX00
Caterpillar BFNDX00 Lafayette 3606 Engine

Buy Lafayette 3606 Engine BFNDX00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BFNDX00:

GAS ENGINE  G3606B   Caterpillar
  For full view, you need register

Information:


Table 4
FMI 06 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Harness For A Short To Battery
A. Turn the key start switch and disconnect switch OFF.
B. Disconnect the machine harness connector from the transceiver.
C. Disconnect the machine harness connectors from the ECM.
D. At the RCM harness connector, measure the resistance between all the other contacts that are used in the RCM and Battery+.
E. At the Transceiver harness, measure the resistance between all the other contacts used in the Transceiver and Battery +.
Each resistance measurements are greater than 5KΩ. OK - All resistance measurements are greater than 5K Ω.
Proceed to Test Step 2.
NOT OK - The resistance is less than 5K Ω. There is a short between the diagnostic circuit and another circuit.
Repair: Repair or replace the machine harness.
Proceed to Test Step 3.
2. Check The Transceiver
A. Turn the key start switch and disconnect switch OFF.
B. Disconnect the machine harness connector from the transceiver.
C. On the Transceiver, measure the resistance between the Pin C (L906) and all other Pins.
Each resistance measurements are greater than 5KΩ. OK - All resistance measurements are greater than 5K Ω.
Proceed to Test Step 3.
NOT OK - The resistance is less than 5K Ω. One or more of the measurements was incorrect.
Repair: Repair or replace the Transceiver.
Proceed to Test Step 3.
3. Check If The Diagnostic Code Remains
A. Reconnect all harness connectors. Return machine to normal operating condition.
B. Turn the key start switch and the disconnect switch ON.
C. Clear all diagnostic codes.
D. Operate the machine.
E. Stop the machine and engage the safety lock lever.
F. Check if the diagnostic code is active.
The diagnostic code is no longer present. OK - The diagnostic code does not exist currently. The initial diagnostic code may have been caused by poor electrical connection or short at one of the harness connections. Resume machine operation.
STOP.
NOT OK - The diagnostic trouble code has not been corrected. If the diagnostic code has not been corrected after performing the procedure a second time, the ECM may require replacement.
Prior to replacing the ECM, always contact the Technical Communicator at your dealership for possible consultation with Caterpillar. This consultation may effect repair time.
Follow the steps in Troubleshooting, "ECM - Replace" if the ECM needs to be replaced.
STOP. All Stop (ASTOP) Transceiver - Test
Remote Control ECM
The following is a list of codes that are associated with the All Stop (ASTOP) Transceiver of the Command for Dozing Operator Console system.
Table 5
Remote Control ECM (MID 126)
DTC Code Description System Response
4701 - 12 All Stop Transceiver - Bad Device or Component Machine Shutdown May occur. Machine stop and low idle will occur. RC Operation is not allowed. Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active

Caterpillar SIS machinery equipment:



Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.