AVSPARE.COM
parts catalog

Lafayette 3608 Engine BGBSX00 - Caterpillar



BGBSX00 Lafayette 3608 Engine Caterpillar parts 3608 Lafayette
Rating:
77
Alternative (cross code) number:
CABGBSX00
BGB-SX00
BGBSX00
Caterpillar BGBSX00 Lafayette 3608 Engine

Buy Lafayette 3608 Engine BGBSX00 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: BGBSX00:

MARINE ENGINE  3608   Caterpillar
  For full view, you need register

Information:

The IR-Illuminators are to be placed on the left and right of the sensor to illuminate both sides of the operator's face in low light conditions. The ideal positions for the IR-Illuminators are low and to the side (away from the frontal direction). The illuminators should also be positioned where the light glare from glasses does not reflect directly into the sensor when looking forward. It is also important to minimize any shadows that may be cast from obstructions such as equipment (usually monitors or radio systems) currently installed in the vehicle or from the operator's arms.Mounting the IR-Illuminators
Illustration 23 g06003803
Exploded view of IR-Illuminator
(17) 2×M2×12 black T6 Torx
(18) P003 cover
(19) 2×P004 axle clamp
(20) 2×2mm×5mm black T6 Torx ST
(21) 2×P004 PCB end mount
(22) P001 PCB
(23) P002 base
(24) P006 mounting plateOnce the position for the IR-Illuminators has been identified, they can be mounted using a suitable counter sunk screw through the two holes in the mounting plate and adjusted as appropriate. Refer to Illustration 23.GPS
Illustration 24 g03871772
GPS cable run
The GPS should be mounted in a position where it can clearly see the sky but is protected from rock fall or other physical damage as much as possible. Depending on the size and style of the truck bed/tray there may be many options. The most common option on a haul truck is on the front railing. Grab rails or mirror frames are often used in over the road vehicles. The GPS cable generally follows the same path as other cables on the truck running towards the electrical compartment.Speaker
The speaker should be in a location that will prevent damage and provide a strong audible alert to the operator. The speaker mounting bracket can be bolted directly to one of two threaded mounting points on the IVS computer mounting bracket. Alternatively, the self-tapping screws can be used to mount the speaker in the cabin or it can be mounted using one of the IVS computer mounting bolts.Vibration Motor
Illustration 25 g03871818
Vibration motor cable run
The following should be considered when mounting the vibration motor:Location - Ensure that the vibration motor cable will reach the computer. Ensure that the location of the vibration motor will not impede the operation of the seat.Screws - If using self-tapping screws to attach the vibrator directly to the operator's seat, ensure that the portion of the screw protruding through the metal will not cause discomfort or injury to the operator or interfere with the seats operation.Cable - Leave sufficient cable length to allow the seat to operate in its full range of movement without damaging the cable. Also protect the cable with split conduit where required.Effectivity - Ensure that the vibration motor is mounted in a location that allows the operator to feel the vibrations through the seat, that is, the vibration motor should be mounted directly to the seat as opposed to the seats mounting bracket, and so on.Troubleshooting
This section is a guide to troubleshoot common DSS faults. If the fault you are experiencing is not listed here or you require further

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.