AVSPARE.COM
parts catalog

Lafayette 3612 Engine BHJBR00 - Caterpillar



BHJBR00 Lafayette 3612 Engine Caterpillar parts 3612 Lafayette
Rating:
27
Alternative (cross code) number:
CABHJBR00
BHJ-BR00
BHJBR00
Caterpillar BHJBR00 Lafayette 3612 Engine

Buy Lafayette 3612 Engine BHJBR00 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: BHJBR00:

MARINE ENGINE  3612   Caterpillar
  For full view, you need register

Information:


To verify the connection on the MS352, connect to the webpage and view the "I/O Configuration" Port Summary page. The 5017 port will be highlighted green.Serial Connection to a Third-Party Receiver
This section covers the connection of a third-party GPS receiver to the "COM" port of the Gen 3.1 or Gen 4.0 DSS module.The customer must consult with the GPS integrator or support channels of the GPS provider to ensure that the required outputs are available and ensure that the correct physical connections can be made to the third-party device.The 245-7310 Control Harness As used to make the serial data connection from the GPS device to the DSS module is intended to be connected to the standard 3-pin circular service connection of a GPS device. If this connection is not available, a unique connection may be created. The Caterpillar part number for the 3-pin connector receptacle is listed below in the optional parts Table 7.Required Output
NMEA GGA at 2 Hz and NMEA RMC at 2 Hz.Required Part
The required part number for connection to a third-party receiver is listed below:
245-7310 Control Harness AsIn addition to the parts required for installation the following parts listed in Table 6 must be purchased from a third-party vendor:
Table 6
Qty Part Number Description Supplier
1 5205980-1 Male Screw Retainer Kit Tyco Electronics Use 5205980-1 for securing the connector to the DSS module.Optional Parts
Optional parts listed in the Table 7 can be used to connect the third-party serial output to 245-7310 Control Harness As cable 3-pin end.The 151-6320 Wire Removal Tool may be needed to remove the wires from the 3-pin connector of 245-7310 Control Harness As.
Table 7
Qty Part Number Description
3 8T-8729 Connector Pin
1 8T-8732 Connector Receptacle
1 151-6320 Wire Removal Tool Connection Procedure
Perform the following procedure to connect third-party satellite receiver and DSS:
Identify the third-party serial output connection of the third-party GPS satellite receiver.
Connect the 3-pin end of 245-7310 Control Harness As to the third-party output by referring to the Table 8.Note: Disassembly of the 3-pin connector may be required. If this is required extract the wires using a 151-6320 Wire Removal Tool and connect them as listed in the below Table 8. If the third-party device has an open connection, the parts listed in the optional parts (Table 7) can be applied to complete the connection.
Table 8
Connector Location 3-Pin Wire Signal
A 979-GN-18 Ground
B 960-OR-18 Rx1 Receive
C 957-PK-18 Tx1 Transmit
Connect the 9-pin end of 245-7310 Control Harness As to the DSS module.Configuration Procedure
The receiver must be configured to output RMC and GGA NMEA strings at 2Hz. Configuration will vary by type. Consult the third-party system integrator for more details.
Illustration 16 g06188883Illustration 16 represents the pin out diagram of 245-7310 Control Harness As.System Overview
Haul Truckwith Cat Fleet using MS352 Satellite Receiver
Illustration 17 g06194077Illustration 17 represents the system overview of Haul Truck with Cat Fleet using the serial connection to an MS352 satellite receiver.
Illustration 18 g06238247Illustration 18 represents the system overview of Haul Truck with Cat Fleet using an Ethernet connection to an MS352 satellite receiver.DSS Module

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.