AVSPARE.COM
parts catalog

Lafayette 3616 Engine BHRNS00 - Caterpillar



BHRNS00 Lafayette 3616 Engine Caterpillar parts G3616 Lafayette
Rating:
83
Alternative (cross code) number:
CABHRNS00
BHR-NS00
BHRNS00
Caterpillar BHRNS00 Lafayette 3616 Engine

Buy Lafayette 3616 Engine BHRNS00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BHRNS00:

GAS ENGINE  G3616   Caterpillar
  For full view, you need register

Information:

Hydraulic Oil System
Service the Filters
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil can cause burns.Remove the fill cap only when the engine is stopped, and the cap is cool enough to touch with your bare hand. Remove the fill cap slowly to relieve pressure.
1. Unlatch and open both right side access doors.2. Pull the latch and open the hydraulic tank cap access cover. The cover opens from the top.3. Slowly remove hydraulic tank filler cap to relieve system pressure.Main Filter and Screen
1. Open rear access door on left side. 2. Remove cap from drain valve (1) and attach a hose with a fitting, with a 1 1/16 - 12 internal thread, to the valve.3. When the hose connection is tightened, keep turning the fitting to open the drain valve.4. Loosen bleed screw (2) and allow filter to drain. Close drain valve and disconnect hose.5. Remove filter cover bolts (3). Install 3 bolts in puller holes (4). Pull cover by turning bolts evenly to prevent binding.6. Remove element and screen. Discard old element.7. Clean the inside of the filter housing.8. Wash cover and filter screen in clean non-flammable solvent. Allow to dry.9. Install new filter element and clean screen.10. Inspect cover seal. Install new seal if used seal is damaged. 11. Install cover. Tighten bolts evenly to avoid seal damage.12. Install and tighten bleed screw.13. Install drain cap.14. Close the access door.Pilot System Filter
1. Remove filter housing drain plug and allow oil to drain. 2. Turn nut at top of filter cover and remove cover and used element. Discard element.3. Clean filter housing.4. Clean and install housing drain plug.5. Install a new filter element.6. Fill housing with clean hydraulic oil.7. Wash cover in clean nonflammable solvent. Replace cover seal if it is damaged.8. Install the cover and tighten it to 58 7 N m (43 5 lb ft).9. Start and run engine for a few minutes. Inspect for leaks.10. With the machine level, position the equipment as shown. Position backhoe linkage on ground with stick and bucket cylinders fully extended. Machine must be level. Position clamshell on ground in open position with stick cylinder fully extended and machine level. 11. Stop engine and observe oil level sight gauge on hydraulic tank.12. Maintain oil level between the ADD and the FULL marks.Case Drain Filter
1. Case drain filter is located on front right side of machine, behind boom. 2. Remove filter housing drain plug (1) and allow oil to drain.3. Loosen filter housing bolt (2) and remove housing and element. Discard used element.4. Clean inside of filter housing and inspect filter housing base seal. Install new seal if it is damaged.5. Install new element in filter housing.6. Install housing and tighten retaining bolt to 52 3 N m (38 2 lb ft). Clean and install drain plug.7. Start and run engine at low idle to fill housing. Stop engine.8. Observe hydraulic oil level. Add if necessary.9. Close and secure all access doors.Fuel System
Service

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.