AVSPARE.COM
parts catalog

Lafayette 3608 Engine BKK1900 - Caterpillar



BKK1900 Lafayette 3608 Engine Caterpillar parts G3608 Lafayette
Rating:
79
Alternative (cross code) number:
CABKK1900
BKK-1900
BKK1900
Caterpillar BKK1900 Lafayette 3608 Engine

Buy Lafayette 3608 Engine BKK1900 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BKK1900:

GAS ENGINE  G3608   Caterpillar
  For full view, you need register

Information:


The spring of the recoil spring assembly is compressed under several tons of force.Do not attempt to compress or release the tension of the spring with the nut on the end of the retaining rod.Damaged threads on the retaining rod or nut can cause the assembly to come apart with force, resulting in injury or death.
Note: Prior to assembling the recoil spring assembly, make sure that Tooling (A) is on a level surface.
Illustration 1 g02723112
Check the condition of the threads on track adjuster (12) and nut (6). If the threads are worn or damaged, use new parts for replacement.
Assemble the recoil spring assembly loosely. Position spring (10) onto support (11). Install support (9) onto track adjuster (12). Install track adjuster (12) into support (11).
Illustration 2 g00483426
Install Tooling (C) on Tooling (B).
Illustration 3 g00494710
Illustration 4 g00483437Note: Two adjustable supports (1), reaction plate (2), and movable plate (3) are part of Tooling (A).
Adjust the spacing between reaction plate (2) and movable plate (3) so that the spacing is approximately the same length as the recoil spring assembly. Also, make sure that two adjustable supports (1) are positioned between the reaction plate and the movable plate, as shown. Level the two supports. Note: The recoil spring assembly may be installed in Tooling (A) from the end. In this case, reaction plate (2) must be removed. Then reinstall the reaction plate after the recoil spring assembly is in place on two adjustable supports (1).
Do not remove the hoist from the recoil spring assembly until the unit is leveled, centered and locked in the specified tooling.
The combined weight of the recoil spring assembly is approximately 116 kg (255 lb).
Fasten a suitable lifting device to the recoil spring assembly. Position the recoil spring assembly on two adjustable supports (1) in Tooling (A).
Adjust the two adjustable supports in order to align the centerline of the recoil spring assembly with the centerline of Tooling (A).
Illustration 5 g00949740
The hoist has been removed from the recoil spring assembly in order to provide a better illustration of level gauge (4).
Operate Tooling (B) and guide the end of the recoil spring assembly through the hole in reaction plate (2). Put a level gauge (4) on the recoil spring assembly. Make sure that the recoil spring assembly is level and centered in Tooling (A). Remove the suitable lifting device from the recoil spring assembly.
Illustration 6 g00498784
Close covers (7) on Tooling (A). Compress the recoil spring assembly with Tooling (B).
Illustration 7 g02723162
Open the covers on Tooling (A). Measure the assembled length of the recoil spring. The Compressed Length must be 550 1.5 mm (22 0.060 inch).
If the assembled length is not correct, close covers (7) on Tooling (A), and adjust the spring length with Tooling (B). If the assembled length is correct, the assembly of the recoil spring assembly can be completed.
Illustration 8 g00711947
Apply a rust inhibitor to the threads on the end of the track adjuster for the recoil spring. Install nut (6). Tighten nut (6).
Put Tooling (D) on the threads of the socket head bolts that

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.