AVSPARE.COM
parts catalog

Lafayette 3606 Engine BKPFP00 - Caterpillar



BKPFP00 Lafayette 3606 Engine Caterpillar parts G3606B Lafayette
Rating:
47
Alternative (cross code) number:
CABKPFP00
BKP-FP00
BKPFP00
Caterpillar BKPFP00 Lafayette 3606 Engine

Buy Lafayette 3606 Engine BKPFP00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BKPFP00:

GAS ENGINE  G3606B   Caterpillar
  For full view, you need register

Information:


Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information.
Before servicing/performing maintenance on the machine, electrical power must be physically disconnected; battery plugs must be disconnected from the batteries, or the trailing cable must be unplugged, and warning tags and padlocks shall be applied by a certified electrician. Certified electricians shall perform or direct any electrical work, including any energized testing, repair work in controllers, motors, or other approved compartments, and shall insure that all compartments are properly closed and inspected prior to re-energization. All applicable lock out and tag out procedures must be followed.
Do not operate the machine if any guards or covers are missing or inadequately secured. Personnel could be seriously injured or machine damage may occur.
Observe the safe working load limits of all lifting and blocking devices and keep a safe distance from suspended/blocked loads. Personnel may be seriously injured or killed by falling loads.
Required Parts
Illustration 1 g06280248
Table 1
Parts in 557-9825 Chain Kit
Item Qty Part Number Part Name
1 1 450-5859 Spring
2 1 557-9823 Shackle
3 1 7X-0312 Bolt
4 1 9M-5048 Locknut
5 4 557-9824 Plate
6 2 557-9822 Chain Link
7 2 8T-8908 Bolt
8 2 2D-6235 Locknut
9 1 558-3572 Chain As
10 1 558-3571 Chain As Installation Procedure
Lower the broom on the ground and tilt forward to remove tension in the chains.
Remove and discard the spring, two chains, and two quick links from the broom.
Illustration 2 g06280263
Coupler frame
(A) 10.9 0.5 mm (0.43 0.02 inch)
(B) Chain holder slot
Grind the full length of the chain holder slot (B) on the coupler frame to make the slot (B) width as per dimension (A). Refer to Illustration 2.
Illustration 3 g06280250
(2) 557-9823 Shackle
Remove and discard the pin and cotter pin that are packaged with shackle (2). Refer to Illustration 3.
Illustration 4 g06280264
Back of the brush frame
(B) Chain holder
(2) 557-9823 Shackle
(3) 7X-0312 Bolt
(4) 9M-5048 Locknut
(6) 557-9822 Chain Link
(9) 558-3572 Chain As
(10) 558-3571 Chain As
Attach shackle (2) to the upper hole on the back of the brush frame using bolt (3) and locknut (4). Refer to Illustration 4.Note: Tighten locknut (4) until the locknut (4) contacts shackle (2).
Secure chain link (6) of chain assembly (9) to the lower hole on the back of the brush frame. Refer to Illustration 4
Slide chain assembly (10) in the chain holder slot (B). Refer to Illustration 4.
Adjust the chain assembly (10) to the proper tension level.Note: Refer to Adjusting Upper Spring-Chain AssemblyOperation and Maintenance Manual, SEBU9264, "BA118C Angle Broom" for adjusting the chain assembly (10).

Caterpillar SIS machinery equipment:



Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.