parts catalog

Lafayette 3608 Engine BKRGC00 - Caterpillar

BKRGC00 Lafayette 3608 Engine Caterpillar parts 3608 Lafayette
Alternative (cross code) number:
Caterpillar BKRGC00 Lafayette 3608 Engine

Buy Lafayette 3608 Engine BKRGC00 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: BKRGC00:

MARINE ENGINE  3608   Caterpillar
  For full view, you need register


Safety Section
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Required Parts
Table 1
Required Parts
Qty Part Number Part Name
2 096-2617 Screw
2 3S-2093 Cable Strap
2 8T-0328 Hard Washer
1 450-7108 Radio As
1 467-4835 Radio Harness As Machine Preparation
Position the machine on level ground.
Release the hydraulic system pressure. Refer to the appropriate Operation and Maintenance Manual, "System Pressure Release" procedure for your machine.
Illustration 1 g00104545
Attach a "Do Not Operate" warning tag to the start switch before you service or repair the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Removal Procedure
Illustration 2 g06012125
Existing radio group (typical example)
(A) Console harness assembly
(A1) Console harness connector
(B) Antenna cable
(C) Right side console
(1) Radio
(1A) Radio connector port
(2) Screws
Remove the covers from right side console (C) to gain access the area around radio (1).
Disconnect console harness assembly connector (A1) from radio (1) connector port (1A).
Remove antenna cable (B) from radio (1).
Remove two screws (2).
Remove the radio from the right side console.Installation Procedure
Table 2
Required Parts
Item Qty Part Number Part Name
1 2 096-2617 Screw
2 2 3S-2093 Cable Strap
3 2 8T-0328 Hard Washer
4 1 450-7108 Radio As
5 1 467-4835 Radio Harness As
Illustration 3 g06012208
(A) Console harness assembly
(B) Antenna cable
(C) Bracket
(1) 096-2617 Screw
(3) 8T-0328 Hard Washer
(4) 450-7108 Radio As
(5) 467-4835 Radio Harness As
Position new radio assembly (4) onto existing bracket (C). Secure the radio assembly to the bracket using two new screws (1) and two new hard washers (3). Tighten the screws to a torque of 4 N m (35 lb in).
Connect new radio harness assembly (5) to radio assembly (4).
Connect the other end of radio harness assembly (5) to existing console harness (A).
Connect existing antenna cable (B) to radio assembly (4).
Illustration 4 g06012276
(A) Console harness
(B) Antenna cable
(2) 3S-2093 Cable Strap
(4A) Red and White jacks
Secure console harness (A) to the existing mounting block on bracket (C) using one new cable strap (2).
Secure red and white jacks (4A) to antenna cable (B) using one new cable strap (2).
Install covers.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.