AVSPARE.COM
parts catalog

Lafayette 3616 Engine BL26100 - Caterpillar



BL26100 Lafayette 3616 Engine Caterpillar parts 3616 Lafayette
Rating:
28
Alternative (cross code) number:
CABL26100
BL2-6100
BL26100
Caterpillar BL26100 Lafayette 3616 Engine

Buy Lafayette 3616 Engine BL26100 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: BL26100:

MARINE ENGINE  3616   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M10 by 100 mm 2 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01983516
Typical example
Illustration 2 g01981253
Remove the bolts from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing to support the flywheel housing. The flywheel housing can weigh 40 kg (88 lb).
Remove bolts (2) and remaining bolts (3) from flywheel housing (1).
Use a suitable lifting device to remove flywheel housing (1) from the cylinder block.
Illustration 3 g01983533
Typical example
Remove dust seal (5).
If necessary, remove dowels (4) from the cylinder block. Do not replace the dowels unless the dowels are damaged.Installation Procedure (Standard Housing)
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M10 by 100 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 4 g01983535
Typical example
Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder block.
Install Tooling (A) to the cylinder block.
Install dust seal (5).
Illustration 5 g01981253
Typical example
Ensure that bolts (2) and bolts (3) are clean and free from oil or grease. Ensure that all threaded holes in the cylinder block are clean and free from oil or grease.
Install a suitable lifting device to the flywheel housing. The flywheel housing can weigh 40 kg (88 lb).
Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (2) and bolts (3).
Remove Tooling (A). Install remaining bolts (3).
Illustration 6 g06188473
Tightening sequence
Illustration 7 g01984554
Identification of the bolt Grade bolts (3) and bolts (2)
Follow Step 11.a through Step 11.b to tighten bolts (3) and bolts (2) in the tightening sequence. Refer to Illustration 6.
Tighten bolts (3) to a torque of 63 N m (46 lb ft).
Tighten bolts (2) to a torque of 78 N m (58 lb ft).
Check the alignment of flywheel housing (1) with the crankshaft. Refer to System Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for the correct procedure.End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.