AVSPARE.COM
parts catalog

Lafayette 3616 Engine BLLNL00 - Caterpillar



BLLNL00 Lafayette 3616 Engine Caterpillar parts G3616 Lafayette
Rating:
18
Alternative (cross code) number:
CABLLNL00
BLL-NL00
BLLNL00
Caterpillar BLLNL00 Lafayette 3616 Engine

Buy Lafayette 3616 Engine BLLNL00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BLLNL00:

GAS ENGINE  G3616   Caterpillar
  For full view, you need register

Information:


Personal injury or death could result when towing a disabled machine incorrectly.Always block both tracks before disengaging the final drives. When the final drives are disengaged, the brakes are also disengaged. The machine can move.Follow the recommendations below, to properly perform the towing procedure.
To tow the machine, both final drives must be disengaged.Do not operate the track motors with the final drives disengaged, or damage could result.
This machine is equipped with spring applied, hydraulic pressure released brakes. If the engine or power train hydraulics are inoperable, the brakes are applied and the machine can not be moved.These towing instructions are for moving a disabled machine a short distance, only a few feet at low speed, no faster than 2 km/h (1.2 mph), to a convenient location for repair. These instructions are for emergencies only. Always haul the machine if long distance moving is required.Shielding must be provided on the towing machine, to protect the operator if the tow line or bar should break.Do not allow operator on the machine being towed, unless the operator can control the steering and/or braking.Before towing, make sure the tow line or bar is in good condition and has enough strength for the towing situation involved. Use a towing line or bar with a strength of at least 1.5 times the gross weight of the towing machine, for a disabled machine stuck in mud or when towing on a grade.Attach the tow line only to the tow hooks on the car body.Do not use a chain for pulling. A chain link may break causing possible personal injury. Use a wire rope cable with loop or ring ends. Use an observer in a safe position to stop the pulling procedure if cable starts to break or unravel. Stop pulling whenever the pulling machine moves without moving the towed machine.Keep the tow line angle to a minimum. Do not exceed a 30° angle from the straight ahead position.Quick machine movement could overload the tow line or bar and cause it to break. Gradual and smooth machine movement will work better.Normally, the towing machine should be as large as the disabled machine. Satisfy yourself that the towing machine has enough brake capacity, weight and power, to control both machines for the grade and distance involved.To provide sufficient control and braking when moving a disabled machine downhill, a larger towing machine or additional machines connected to the rear could be required. This will prevent it from rolling uncontrolled.The different situation requirements cannot be given, as minimal towing machine capacity is required on smooth level surfaces to maximum on inclines or poor surface conditions.215C Final Drive Disengagement
1. To disengage a final drive, block the tracks. Remove the thrust plug (1) from the center of the final drive case. Remove the puller bolt and washer (2) from the storage hole on the final drive case. 2. Install and tighten the puller bolt until the sun gear is pulled out of engagement with the planet gears. Torque lockup may require

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.