AVSPARE.COM
parts catalog

Lafayette 3616 Engine BLN1900 - Caterpillar



BLN1900 Lafayette 3616 Engine Caterpillar parts G3616 Lafayette
Rating:
80
Alternative (cross code) number:
CABLN1900
BLN-1900
BLN1900
Caterpillar BLN1900 Lafayette 3616 Engine

Buy Lafayette 3616 Engine BLN1900 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: BLN1900:

GAS ENGINE  G3616   Caterpillar
  For full view, you need register

Information:


Illustration 3 g00684977
Remove pin (3) and O-ring seal (4).
Illustration 4 g00684979
Remove bolts (5) that fasten differential and bevel gear (6) to the axle assembly.
Illustration 5 g00684981
Attach Tooling (B) to differential and bevel gear (6), as shown.
Attach a suitable lifting device to Tooling (B).
Install bolts (5) in the threaded holes of differential and bevel gear (6). Tighten the bolts evenly to separate the differential and bevel gear from the housing.
Illustration 6 g00684982
Remove differential and bevel gear (6). The weight of differential and bevel gear (6) is approximately 590 kg (1300 lb).
Illustration 7 g00684984
Remove O-ring seal (7).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 4C-6486 Stand 2
8S-7615 Pin 2
8S-8048 Saddle 2
8S-7611 Tube 2
B 138-7576 Link Bracket 3
C 1U-7234 Feeler Gauge 1
Illustration 8 g00684984
Install O-ring seal (7).
Illustration 9 g00684982
Attach Tooling (B) and a suitable lifting device to differential and bevel gear (6).
Install differential and bevel gear (6) in the axle housing. The weight of differential and bevel gear (6) is approximately 590 kg (1300 lb).
Illustration 10 g00684979
Remove Tooling (B) and the suitable lifting device.
Install bolts (5). Tighten bolts (5) to a torque of 230 30 N m (170 22 lb ft) plus an additional 120 degrees 10 degrees.
Illustration 11 g00684977
Install O-ring seal (4) on pin (3).
Lubricate pin (3) and O-ring seal (4) with oil. Install pin (3) in the axle housing.
Illustration 12 g01147049
Install cover (1) without shims.
Install bolts (2). Tighten bolts (2) enough to remove the end play between pin (3) and cover (1).
Use Tooling (C) to measure the gap between the cover and the axle housing. Record this measurement. Use this measurement to determine the correct thickness of required shims.
Install a thickness of shims that will establish a −0.03 mm (−0.001 inch) preload to a 0.03 mm (0.001 inch) end play in pin (3).
Illustration 13 g00684976
Install cover (1) with the measured number of shims.
Install bolts (2). Tighten bolts (2) to a torque of 105 20 N m (78 15 lb ft).

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.