parts catalog

Lafayette 3612 Engine BLSFD00 - Caterpillar

BLSFD00 Lafayette 3612 Engine Caterpillar parts 3612 Lafayette
Alternative (cross code) number:
Caterpillar BLSFD00 Lafayette 3612 Engine

Buy Lafayette 3612 Engine BLSFD00 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: BLSFD00:

MARINE ENGINE  3612   Caterpillar
  For full view, you need register


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components of the engine oil pump are clean and free from wear or damage.
Illustration 1 g01478152
Typical example
Install inner rotor (16) and install outer rotor (17). Used rotors should be installed in the original direction of rotation. Check the clearance between the outer rotor and the body of the oil pump. Check the clearance between the inner rotor and the outer rotor. Check the end play of the rotor assembly. Refer to Specifications, "Engine Oil Pump" for more information.
Lubricate the assembly of the oil pump with clean engine oil. Install front cover (15). Install bolts (14). Tighten the bolts to a torque of 26 N m (19 lb ft).
Ensure that the shaft of the oil pump is clean and dry. Position gear (13) onto the shaft. Install nut (12). Tighten the nut to a torque of 95 N m (70 lb ft). Note: Do not use a timing pin to lock the balancer in order to tighten nut (12).
Lubricate hub (9), thrust washer (11) and the bush of idler gear (10) with clean engine oil. Install hub (9) and thrust washer (11) to idler gear (10). Note: Ensure the correct orientation of the idler gear.
Install the assembly of the idler gear to balancer (1).
Ensure that the threads of bolt (8) are clean and dry. Apply Tooling (E) to the threads of the bolt. Install bolt (8). Tighten the bolt to a torque of 26 N m (19 lb ft).
Check the end play of idler gear (10). Refer to Specifications, "Engine Oil Pump".
Install the engine oil relief valve . Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install" for further information. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 230-6284 Timing Pin (Crankshaft) 1
C 231-8849 Timing Pin (Balancer) 1
F 9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
G - Guide Bolt
M10 by 75mm 2
Illustration 2 g01259627
Ensure that No. 1 piston is at the top center position and that Tooling (B) is installed to Position (X) in the front housing.
Clean the faces of the cylinder block.
Illustration 3 g01252312
Install Tooling (G) to the cylinder block.
Illustration 4 g01260306
Ensure that dowel (6) and dowel (7) are seated in the housing of balancer (1).
Illustration 5 g01252310
Install Tooling (C) to balancer (1). Ensure that Tooling (C) is engaged into shaft (5).
Attach a suitable lifting device to the balancer. The balancer weighs approximately 23 kg (51 lb).
Use the lifting device to align balancer (1) with Tooling (G). Install the balancer to the cylinder block. Ensure that dowels (6) and (7) are aligned with the holes in the cylinder block. Ensure that gear (10) and the crankshaft gear mesh. Remove the lifting device.
Illustration 6 g01259635
Install bolts (4) to balancer (1) finger tight.
Remove Tooling (G) and install remaining bolts (4). Tighten the bolts to a torque of 54 N m (40 lb ft).
Remove Tooling (B) and Tooling (C).
Install suction

Caterpillar SIS machinery equipment:

Caterpillar SIS

Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.