AVSPARE.COM
parts catalog

Lafayette 3616 Engine FMSYD00 - Caterpillar



FMSYD00 Lafayette 3616 Engine Caterpillar parts G3616 Lafayette
Rating:
13
Alternative (cross code) number:
CAFMSYD00
FMS-YD00
FMSYD00
Caterpillar FMSYD00 Lafayette 3616 Engine

Buy Lafayette 3616 Engine FMSYD00 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: FMSYD00:

GAS ENGINE  G3616   Caterpillar
  For full view, you need register

Information:

4. Measure distance (A) which is the existing total clearance.5. Determine the thickness of shim(s) that needs to be removed from shim group (1) installed at location (B), by calculating as follows. Thickness of shims to be removed: Total clearance (A) - [0.5 to 1.0 mm (.02 to .04 in)]6. Remove an appropriate number of shim(s), meeting the above calculation. Be sure to use a minimum of three 0.5 mm (.02 in) shims. To remove shims, remove bolts (4), washers (5) and plate (3).7. After correct number of shims have been removed, install plate (3), washers (5) and bolts (4) with pin (2) aligned with pin hole. Tighten bolts (4) to a torque of 100 20 N m (70 15 lb ft).8. After installation, make sure that clearance (A) is still correct.Air Conditioner (If Equipped)
Clean Air Filter Elements
An air filter element plugged with dust will result in decreased performance and service life of the air conditioner (if equipped).To prevent decreased performance, clean the air filter elements, as required.
The air filter elements are located at the front, right and left sides of the air conditioner unit in the cab.Use the following procedure to clean the air filter elements. 1. Remove air filter (1) from the front side of the unit and air filters (2) from the right and left sides.2. Clean the filter elements using a maximum of 200 kPa (28 psi) pressure air or water.3. Inspect the filters after cleaning. If they are damaged or badly contaminated, use new filter elements. Before installing filter element, make sure they are dry.4. Reverse Steps 1 and 2 for air filter element installation.Tracks
Check/Adjust
Grease is under high pressure.Grease coming out of the relief valve under pressure can penetrate the body causing injury or death.Do not watch the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened.Loosen the relief valve one turn only.If track does not loosen, close the relief valve and contact your Caterpillar dealer.
Keeping the track properly adjusted will increase the service life of the track and drive components.The track tension has to be set as required by the current operating conditions. Use as slack a track as possible if the soil is heavy.
Measuring Track Tension
1. Place a straight edge, long enough to reach from the idle wheel (or final drive) to the carrier roller, on the tracks.2. Measure the maximum amount of track sag from the high point of the track grouser to the bottom of the straight edge. Properly adjusted track will have approximately 40 to 55 mm (1 5/8 to 2 1/8 in) slack.Track Tightening
Wipe the fill valve fitting before lubricating. 1. Add grease through fill valve fitting (1) until the correct track tension is reached.2. Operate the machine back and forth to equalize the pressure.3. Check the amount of track sag again and adjust as necessary.Track Loosening
1. Loosen relief valve (2) carefully (one turn maximum) until the track begins to loosen.2.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lafayette Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.