2U9949 LATCH AS Caterpillar parts
CB-534D, CB-564D
Rating:
Alternative (cross code) number:
CA2U9949
2U-9949
2U9949
CA2U9949
2U-9949
2U9949
Weight: 0.07 pounds 0 kg.
VIBRATORY COMPACTOR,
Number on catalog scheme:
2
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores.Note: A number with four digits is stamped on the gasket in order to ensure the correct positioning of the gasket. This number faces the cylinder head. Make sure that the cylinder head is the correct thickness before installation.
Place the cylinder head gasket on the dowels on the top of the cylinder block. Do not use any gasket sealant or compound on the cylinder head gasket.
Illustration 1 g00597552
Attach a suitable lifting device to cylinder head (7) .
Place cylinder head (7) on the cylinder block. Ensure that the cylinder head is positioned on the dowels and that the cylinder head gasket is positioned correctly.
Lubricate the cylinder head bolts with clean engine oil.
Illustration 2 g00454966
Bolt tightening sequence for 3 cylinder enginesThe arrow points toward the front of the engine.
Illustration 3 g00597449
Bolt tightening sequence for 4 cylinder enginesThe arrow points toward the front of the engine.
Install the cylinder head bolts and gradually tighten the cylinder head bolts in a numerical sequence. The numerical sequence is shown in Illustration 2 and in Illustration 3. Tighten the cylinder head bolts to the following torque: 3003 Engine ... 51 N m (38 lb ft) 3013, 3014, and 3024 Engines ... 100 N m (74 lb ft)
Illustration 4 g00597219
Position external oil line (5) on the side of the engine and install bolt (6) .
Illustration 5 g00597210
Install bolt (4) and the two washers that fasten external oil line (5) to the front of the cylinder head.
Illustration 6 g00597200
Install nut (3) (not shown) that connects the external oil line to the fuel injection pump.
Install fuel hose (2) on the fuel injection pump and tighten hose clamp (1) .End By:
On 3013, 3014, and 3024 engines, install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
On 3013 engines, install the water temperature regulator housing. Refer to Disassembly and Assembly, "Water Temperature Regulator Housing - Remove and Install".
On 3003 engines, install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Install".
On 3003 engines, install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores.Note: A number with four digits is stamped on the gasket in order to ensure the correct positioning of the gasket. This number faces the cylinder head. Make sure that the cylinder head is the correct thickness before installation.
Place the cylinder head gasket on the dowels on the top of the cylinder block. Do not use any gasket sealant or compound on the cylinder head gasket.
Illustration 1 g00597552
Attach a suitable lifting device to cylinder head (7) .
Place cylinder head (7) on the cylinder block. Ensure that the cylinder head is positioned on the dowels and that the cylinder head gasket is positioned correctly.
Lubricate the cylinder head bolts with clean engine oil.
Illustration 2 g00454966
Bolt tightening sequence for 3 cylinder enginesThe arrow points toward the front of the engine.
Illustration 3 g00597449
Bolt tightening sequence for 4 cylinder enginesThe arrow points toward the front of the engine.
Install the cylinder head bolts and gradually tighten the cylinder head bolts in a numerical sequence. The numerical sequence is shown in Illustration 2 and in Illustration 3. Tighten the cylinder head bolts to the following torque: 3003 Engine ... 51 N m (38 lb ft) 3013, 3014, and 3024 Engines ... 100 N m (74 lb ft)
Illustration 4 g00597219
Position external oil line (5) on the side of the engine and install bolt (6) .
Illustration 5 g00597210
Install bolt (4) and the two washers that fasten external oil line (5) to the front of the cylinder head.
Illustration 6 g00597200
Install nut (3) (not shown) that connects the external oil line to the fuel injection pump.
Install fuel hose (2) on the fuel injection pump and tighten hose clamp (1) .End By:
On 3013, 3014, and 3024 engines, install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
On 3013 engines, install the water temperature regulator housing. Refer to Disassembly and Assembly, "Water Temperature Regulator Housing - Remove and Install".
On 3003 engines, install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Install".
On 3003 engines, install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Caterpillar parts catalog:
Parts latch Caterpillar catalog:
1722384
LATCH AS-ROTARY
CB-434D, CB-534D, CB-564D, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K LGP, D6N, D6N LGP, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
CB-434D, CB-534D, CB-564D, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K LGP, D6N, D6N LGP, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
1722385
LATCH AS-ROTARY
CB-434D, CB-534D, CB-564D, CD-54, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K LGP, D6N, D6N LGP, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
CB-434D, CB-534D, CB-564D, CD-54, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K LGP, D6N, D6N LGP, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
320C, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 5080, 5090B, 931C II, CB-534D, CB-564D, D3B
2171514
LATCH
CB-434D, CB-534D, CB-564D, CB-634D, CP-433E, CS-423E
CB-434D, CB-534D, CB-564D, CB-634D, CP-433E, CS-423E
2578697
LATCH AS
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D
2578698
LATCH AS
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D
2182207
LATCH AS-DOOR
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E, BG600D, BG655D, CB-54, CB-64, CD-54, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-42...
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E, BG600D, BG655D, CB-54, CB-64, CD-54, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-42...
2171514
LATCH
CB-434D, CB-534D, CB-564D, CB-634D, CP-433E, CS-423E
CB-434D, CB-534D, CB-564D, CB-634D, CP-433E, CS-423E
1642256
LATCH-SPRING
CB-214D, CB-214E, CB-22, CB-334E, CB-34
CB-214D, CB-214E, CB-22, CB-334E, CB-34
1723185
LATCH AS
CB-214D, CB-214E, CB-22, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
CB-214D, CB-214E, CB-22, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
1318932
LATCH
320B, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321B, 321C, 321...
320B, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321B, 321C, 321...
1851876
LATCH
CB-334D, CB-334E, CB-335D, CB-34
CB-334D, CB-334E, CB-335D, CB-34
2951414
LATCH AS
CP-56, CP-64, CP-76, CS-563E, CS-64, CS-74
CP-56, CP-64, CP-76, CS-563E, CS-64, CS-74
1C3750
LATCH
AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E, BG600D, BG655D, CS-563E
AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E, BG600D, BG655D, CS-563E
1981088
LATCH AS
AP-655C
AP-655C
2384489
LATCH AS-DOOR
CB-434D
CB-434D
2578698
LATCH AS
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D
2578697
LATCH AS
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D