LATCH-DOOR 4851019 - Caterpillar

Mounting location on Beta machines 246D, 262D, 277D, 279D, 287D, and 289D
Illustration 3 g06064646
(A) 254.0 mm (10.00 inch)
(B) 179.0 mm (7.05 inch)
(C) 329.0 mm (12.95 inch)
(D) 99.2 mm (3.91 inch)
(E) 159.2 mm (6.27 inch)
(F) Diameter is 21.0 mm (0.83 inch)
(G) Diameter is 7.0 mm (0.28 inch)Note: All the dimensions are referenced from the bottom and side of the machine engine enclosure.Mounting location on Beta+ machines 272D2, 272D2-XHP, 297D2, 297D2-XHP, 299D2, and 299D2-XHP
Illustration 4 g06064649
(A) 301.8 mm (11.88 inch)
(B) 226.8 mm (8.93 inch)
(C) 376.8 mm (14.83 inch)
(D) 97.5 mm (3.84 inch)
(E) 144.0 mm (5.67 inch)
(F) Diameter is 21.0 mm (0.83 inch)
(G) Diameter is 7.0 mm (0.28 inch)Note: All the dimensions are referenced from the bottom and side of the machine engine enclosure.
Locate the hole locations for mounting the license plate kit on the respective machines as shown in the Illustration 1, Illustration 2, Illustration 3, and Illustration 4.
Drill two holes of a diameter 7.0 mm (0.28 inch) and one hole of a diameter 21.0 mm (0.83 inch) on the machine engine enclosure as shown in the Illustration 1, Illustration 2, Illustration 3, and Illustration 4.Mounting the registration plate lamp group on the bracket Assembly
Illustration 5 g06066424
(1) 190-8962 Registration Plate Lamp Gp
(2) 8P-8540 Grommet
(3) 6V-9672 Screw
(4) 5C-8312 Nut
(5) 4B-4863 Washer
(6) 498-4931 Bracket As
Remove the top glass on the registration plate lamp group (1).
Install the registration plate lamp group (1) on the bracket assembly (6) by using grommet (2), two washers (5), two nuts (4) and two screws (3) and tighten to a torque of 1.70 0.25 N m (15.05 2.21 lb in).
Illustration 6 g06066428
(1) 190-8962 Registration Plate Lamp Gp
(6) 498-4931 Bracket As
Bracket assembly (6) with the registration plate lamp group (1) mounted on it.Installing the 504-1553 Mounting Kit on the Engine enclosure
Illustration 7 g06066430
(6) 498-4931 Bracket As
(7) 9X-2045 Screw
Position the mounting kit on the holes which are already drilled.
Install the mounting kit on the enclosure door of the engine where two holes of diameter 7.0 mm (0.28 inch) is drilled using two screws (7).Connecting the mounting kit harness with the platform harness
Illustration 8 g06066433
(8) 500-3006 Lighting Harness As
Route the lighting harness assembly (8) through drilled hole as shown in Illustration 1. Indicated as (F).
Disconnect RL-C22 (J) connector from the 258-0930 Stop and Tail Lamp Gp.
Connect the LJ-C2 (H) connector of lighting harness assembly (8) to the RL-C22 (J) of the left platform harness. Refer Table 3 and 2 to confirm connector configuration.
Illustration 9 g06066436
Connect the 258-0930 Stop and Tail Lamp Gp (K) to the LJ-C3 (L) connector of lighting harness assembly (8). Refer Table 4 to confirm connector configuration.
Illustration 10 g06066438
(M) Engine enclosure door
(N) Mounting kit
Machine with mounting kit fitted.