AVSPARE.COM
parts catalog

LEVER AS 2141492 - Caterpillar


2141492 LEVER AS Caterpillar parts R2900, R2900G
Rating:
61
Alternative (cross code) number:
CA2141492
214-1492
2141492
Caterpillar 2141492 LEVER AS
Weight: 1890 pounds 857 kg.

Buy LEVER AS 2141492 Caterpillar genuine, new aftermarket tractor parts with delivery
LOAD HAUL DUMP,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$12.10
 

09 May 2018
11 Hundredths Pounds
CNH INDUSTRIAL: CNH INDUSTRIAL
214-1492 CNH GENUINE OEM CLAMP, HOSE
214-1492 || CLAMP || CLAMP, HOSE || All CNH comes with 6 month warranty
Number on catalog scheme: 17
  For full view, you need register

Compatible equipment models: 2141492:

LOAD HAUL DUMP  R2900   R2900G   Caterpillar

Information:


Illustration 1. Early bottom guard group which has a 9P9943 Guard Assembly.
Illustration 2. Current bottom guard group which has a 3T2224 Guard Assembly.When installed, the 9P9989 Guard Assembly is in front of the pivot shaft and either the 9P9943 or the 3T2224 Guard Assembly is under the pivot shaft. The only connections between the two units are three support brackets at the front of the 9P9943 or 3T2224 Guard Assembly. Some servicemen think these brackets look like hinges, but they are not. They are only supports. The brackets are used to permit easier access to the pivot shaft and to permit the guard and guard assembly to move separately as the the machine twists during operation.
The rear guard does not have hinges, and it will fall if it is not properly supported when the mounting bolts are removed. Personal injury or death can result if the guard falls on a person. Support guard with the jack in the tool chart or an equivalent support before removal of the mounting bolts.
If the plate bearing against the guard is not level, the guard can slide off the jack while it is being lowered or raised. This could result in personal injury or death to the serviceman. Be sure the plate is level before removing mounting bolts. See Illustration 3.
Procedure For Removal And Installation Of Bottom Guard Which Uses A 9P9943 Guard Assembly
1. Put tool A under the 9P9989 Guard Assembly. Remove the four nuts and washers from the bolts that fasten the guard to the machine. Lower and remove the guard assembly. See Illustration 3.
Illustration 3. Use of tool A to remove the 9P9989 Guard Assembly.2. Put tools B and C under the 9P9943 Guard Assembly. Tighten the clamps for tool B on the guard. Remove the bolts that fasten the guard to the machine. Remove the guard with the tools. See Illustration 4.3. Use tools B and C to put the 9P9943 Guard Assembly into position. Install the bolts that fasten it to the machine.4. Use tool A to put the 9P9989 Guard Assembly into position. Install the nuts and washers that fasten it to the machine.
Illustration 4. Use of tool B and C to remove the 9P9943 Guard Assembly.Procedure For Removal And Installation Of Bottom Guard Which Uses A 3T2224 Guard Assembly
1. Put tool A under the 9P9989 Guard Assembly as shown in Illustration 3. Remove the four nuts and washers that fasten the guard to the machine. Use tool A to lower and remove the guard assembly.2. Put tool A in position under the 3T2224 Guard Assembly as shown in Illustration 5. Remove the bolts that fasten the guard assembly to the machine. Use tool A to lower and remove the guard assembly.3. Use tool A to put the 3T2224 Guard Assembly into position. Install the bolts that fasten the guard assembly to the machine.4. Use tool A to put the 9P9989 Guard Assembly into position. Install the nuts and washers that fasten it to the machine.
Illustration

Caterpillar parts catalog:

Caterpillar parts catalog
R2900G Load Haul Dump NLK00001-UP (MACHINE) POWERED BY C15 Engine
R2900G Load Haul Dump JLK00001-UP (MACHINE) POWERED BY C15 Engine
R2900 Load Haul Dump ZLK00001-UP (MACHINE) POWERED BY C15 Engine


Parts lever Caterpillar catalog:

4M1853 LEVER AS-SHIFT
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
2586198 LEVER
R1700G, R2900, R2900G
3020056 LEVER
R2900, R2900G
1152261 LEVER AS
AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, R2900, R2900G
2490505 LEVER
R2900, R2900G
3007184 LEVER-TREADLE
R1300, R1600, R1700 II, R2900
2227351 LEVER
R1600, R1600G, R1600H, R1700G, R2900G, R3000H
1869270 LEVER AS
R1300, R1300G, R1300G II
2106285 LEVER
AD45B, AD55, AD55B, AD60, R1300, R1300G, R1300G II
2355516 LEVER-THROTTLE
R1300, R1300G, R1300G II
1868532 LEVER AS
R1700 II, R1700G
2886067 LEVER
R1600H, R1700G
2417957 LEVER
R1600, R1600G, R1600H, R1700G
3320819 LEVER
R2900G, R3000H
1982392 LEVER AS
R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.