2799658 LEVER Caterpillar parts
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
Rating:
Alternative (cross code) number:
CA2799658
279-9658
2799658
CA2799658
279-9658
2799658
Weight: 0.52 pounds 0 kg.
MOTOR GRADER,
Compatible equipment models: 2799658:
Information:
Illustration 3 g01721370
8T-0455 Liner Projection Tool Group (5) Bolt (6) Dial indicator (7) Gauge body (8) Gauge block
Loosen bolt (5) until dial indicator (6) can be moved. Place gauge body (7) and dial indicator (6) on the long side of gauge.
Slide dial indicator (6) into the correct position. When the point of the dial indicator contacts gauge block (8) , the dial indicator is in the correct position. Slide the dial indicator until the needle of the gauge makes a quarter of a revolution clockwise. The needle should be in a vertical position. Tighten bolt (5) and zero the dial indicator.
Illustration 4 g01721372
Measure the liner projection. (6) Dial indicator (7) Gauge body
Place gauge body (7) on the plate for the cylinder block. The indicator point should be on the liner flange. Read the dial indicator in order to find the amount of liner projection. Check the projection at four locations (every 90 degrees) around each cylinder liner.
Table 3
Specifications    
Liner Projection    
0.06 to 0.18 mm ( 0.0024 to 0.0071 inch)    
Maximum Variation in Each Liner    
0.050 mm (0.0020 inch)    
Maximum Average Variation Between Adjacent Liners    
0.08 mm (0.0031 inch)    
Maximum Variation Between All Six Liners    
0.100 mm (0.0040 inch)    
If a liner does not meet the recommended cylinder liner projection specification, check the following parts:
The depth of the cylinder block bore should be 100.00 0.03 mm (3.937 0.001 inch).
The liner flange should be 100.12 0.03 mm (3.942 0.001 inch).If the dimensions for the liner flange do not match the specifications, replace the liner. Then repeat the liner projection measurements. If the dimensions for the depth of the cylinder block bore do not match the specifications, replace the cylinder block. Then repeat the liner projection measurements. C15 Through C18 Procedure
Table 4
Required Tooling    
Part Number    Part Description    Qty    
8T-0455     Liner Projection Tool Group     1    
Table 5
Required Components for C15 Through C18    
Item    Part Number    Description    Quantity For One Cylinder    Quantity For Six Cylinders    
1     7H-3598     Track Bolt     6     36    
2     8F-1484     Washer     6     36    
3     7K-1977     Washer     6     36    
Illustration 5 g00443044
Note: Refer to Reuse and Salvage Guidelines, SEBF9390, "Visual Inspection of Liner Seats for 3400, C15, C16, and C18 Series Engines" for the correct cylinder top deck and spacer plate inspection procedures prior to measuring the liner projection.
Install a new spacer plate gasket and a clean spacer plate.
Install the washers. Install all bolts or the six bolts around the liner.Torque for bolts ... 95 N m (70 lb ft)
Use the 8T-0455 Liner Projection Tool Group to measure the liner projection at "A", "B", "C" and "D".
Record measurements for each cylinder.
Add the four readings for each cylinder. Divide the sum by four in order to find the average.
Table 6
Specifications for C15 Through C18    
Liner Projection    
0.025 to
Cat SIS web machinery list:
Parts lever Caterpillar catalog:
3200355
LEVER
BH150
BH150
2699408
LEVER AS
BH150
BH150
2991020
LEVER AS
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M
2991021
LEVER AS
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M
3541204
LEVER AS
16M
16M
2876155
LEVER
14M, 16M
14M, 16M
3960053
LEVER
MH3049, MH3059
MH3049, MH3059
2869511
LEVER AS
M325D L MH, M325D MH, M330D, MH3037, MH3049, MH3059
M325D L MH, M325D MH, M330D, MH3037, MH3049, MH3059
4364932
LEVER
MH3037
MH3037
3956952
LEVER
MH3037
MH3037
3956951
LEVER
MH3037
MH3037
4180171
LEVER-FEEDBACK
HM825, MD-250
HM825, MD-250