AVSPARE.COM
parts catalog

LEVER 2H9172 - Caterpillar



2H9172 LEVER Caterpillar parts D337 LEVER
Rating:
47
Alternative (cross code) number:
CA2H9172
2H-9172
2H9172
Caterpillar 2H9172 LEVER

Buy LEVER 2H9172 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: 2H9172:

MARINE ENGINE  D337   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:

Start By:a. remove sprocket hubs 1. Drain the oil from the final drive cover.2. Engage the brakes and remove locknut (1) with tool (A). 3. Install tool (B) on the end of the sprocket shaft. Install tool (C) and fasten a hoist.4. Remove nuts (2) and bolts (3) that hold the cover to the steering clutch case. 5. Install two 3/8" - 16 NC forcing screws (4). Tighten the forcing screws evenly and remove the sprocket shaft, gear and cover as a unit. Use bar (5) inside of tool (B) to keep the unit in balance when it is removed. The weight is 108 kg (240 lb.). 6. Remove sprocket shaft (6) and gear from cover (7) with tooling (D) and a press.7. Remove cover (7) from the press. The weight is 56 kg (125 lb.). Remove sprocket shaft (6) and gear from the press. The weight is 52 kg (115 lb.). 8. Remove retainer (8) and bearing cone (9) from the cover. 9. Remove O-ring seal (10) from retainer (8). 10. If a replacement is needed, remove bearing cup (11), spacer (12) and bearing cup (13) from the cover. Do not remove race and roller assembly (14) unless a replacement is needed. The bearing can be damaged when removed.11. Remove race and roller assembly (14) from the cover with tool (E). 12. Remove spacer (15) from the sprocket shaft (6).13. Remove nuts and bolts (16) that hold the sprocket shaft and gear together. Remove gear (17). 14. Remove bearing cone (18) from the sprocket shaft with tooling (F). 15. If a replacement is needed, remove bearing race (19) from the sprocket shaft. 16. Remove bearing cage (20) from the steering clutch case. Do not remove race and roller assembly (21) unless a replacement is needed. The bearing can be damaged when removed.17. Remove race and roller assembly (21) from bearing cage (20).Install Sprocket Shaft, Gear And Cover, As A Unit
1. Install race and roller assembly (21) in bearing cage (20) with tooling (G) and a press. 2. Install bearing cage (20) on the steering clutch case. 3. If bearing race (19) was removed, heat bearing race (19) to a maximum temperature of 135° C (275° F). Install bearing race (19) on the sprocket shaft. If necessary, use tooling (H) to install the bearing race. 4. Install bearing cone (18) on sprocket shaft (6) with tooling (I). Use a force of 98 to 240 kN (11 to 27 ton). 5. Install gear (17) on sprocket shaft (6). Install the bolts and nuts that hold the gear and sprocket shaft together. Tighten the nuts to a torque of 80 7 N m (60 5 lb.ft.). Turn the nuts an additional 120° 5°. Minimum torque must be 307 N m (230 lb.ft.). 6. Lower the temperature of bearing cups (13) and (11). Install bearing cup (13) spacer (12) and bearing cup (11) in the cover. 7. If the race and roller assembly was removed, install the race

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455


Parts lever Caterpillar catalog:

7F7262 LEVER ASSEM.
D326F, D330A, D337, D337F
2F9351 LEVER
D315, D326F, D330A, D337, D337F
8F7849 LEVER
D326F, D337, D342, D397D
8F5607 LEVER
D326F, D337, D337F
1H3792 LEVER ASSEM.
D326F, D337, D337F, D342, D342C, D375D, D397D
8F5607 LEVER
D326F, D337, D337F
1L1546 LEVER
D326F, D337, D337F, D342, D375D, D397D
1L5392 LEVER
528, 657E, D326F, D337F, D342
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.