3941261 LEVER Caterpillar parts
CB-44B, CB-54B
Rating:
Alternative (cross code) number:
CA3941261
394-1261
3941261
CA3941261
394-1261
3941261
Weight: 0.42 pounds 0 kg.
VIBRATORY COMPACTOR,
Number on catalog scheme:
2
For full view, you need register
Information:
ensure that replacement of the ECM is necessary prior to replacement. The ECM is seldom the cause of a diagnostic code. Always check that the proper ground and power are available to the ECM. Before replacing ECM, contact your dealership for possible consultation with Caterpillar.Note: Corrupted configuration software or the wrong software may cause an ECM to report diagnostic codes incorrectly. Prior to replacing the ECM, flash the ECM with the correct configuration software to verify that the failure is unrelated to the corrupted software. See Testing and Adjusting, "ECM - Flash Program".Note: New electronic control modules are available either programmed for a particular machine or unprogrammed. An ECM that has not been programmed must be programmed by using the Cat® Electronic Technician (Cat ET). See Troubleshooting, "ECM - Flash Program". See item 6 to determine whether the ECM has been programmed.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the ECM.
Remove the ECM.cv
Ensure that the replacement ECM has the correct part number.
Connect the machine harness to the ECM.
Determine whether the ECM has been programmed. Connect the Cat ET to the service tool connector. The Cat ET communicates to the ECM.The Cat ET will indicate whether the ECM has been programmed. An ECM that has not been programmed must be programmed by using the WinFlash software which is contained in the Cat ET. See Troubleshooting, "ECM - Flash Program".The ET will provide access to the ECM, if the ECM has already been programmed.Note: Some Variations in the Cat ET menu may be experienced. View the proper subject for information about a specific Cat ET menu.Note: Performance will be affected by any calibration procedures that are omitted. Make sure that all calibration procedures are performed. Perform all calibration procedures, even if the replacement ECM was acquired from a similar machine.Note: The profile of the operator will be lost when the ECM is replaced.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the ECM.
Remove the ECM.cv
Ensure that the replacement ECM has the correct part number.
Connect the machine harness to the ECM.
Determine whether the ECM has been programmed. Connect the Cat ET to the service tool connector. The Cat ET communicates to the ECM.The Cat ET will indicate whether the ECM has been programmed. An ECM that has not been programmed must be programmed by using the WinFlash software which is contained in the Cat ET. See Troubleshooting, "ECM - Flash Program".The ET will provide access to the ECM, if the ECM has already been programmed.Note: Some Variations in the Cat ET menu may be experienced. View the proper subject for information about a specific Cat ET menu.Note: Performance will be affected by any calibration procedures that are omitted. Make sure that all calibration procedures are performed. Perform all calibration procedures, even if the replacement ECM was acquired from a similar machine.Note: The profile of the operator will be lost when the ECM is replaced.
Caterpillar parts catalog:
Parts lever Caterpillar catalog:
3561743
LEVER
CP-54B, CP-68B, CP-74B, CS-56B, CS-78B
CP-54B, CP-68B, CP-74B, CS-56B, CS-78B
3851148
LEVER
CW-34
CW-34
3851126
LEVER AS
CW-34
CW-34
3986775
LEVER
CW-34
CW-34
3609101
LEVER-STOP
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
3656051
LEVER AS
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
0830189
LEVER
PS-300, PS-500
PS-300, PS-500
0829699
LEVER AS
PS-500
PS-500
0829760
LEVER AS
PS-500
PS-500
0829658
LEVER AS
PS-500
PS-500
4322364
LEVER GP
CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
4168779
LEVER GP
CB-44B, CB-54B
CB-44B, CB-54B