AVSPARE.COM
parts catalog

LEVER ASSEM. (R.H.) 5V3787 - Caterpillar



5V3787 LEVER ASSEM. (R.H.) Caterpillar parts 966C LEVER
Rating:
20
Alternative (cross code) number:
CA5V3787
5V-3787
5V3787
Caterpillar 5V3787 LEVER ASSEM. (R.H.)
Weight: 267 pounds 121 kg.

Buy LEVER ASSEM. (R.H.) 5V3787 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

You can buy parts: .

 
$909.15

12 Aug 2020
5V3787 Lever A - Fits: 966C 966R
Compatible Models - 966C 966R || Related Items - 3B8489 7K9213 || Interchange - 7K9695 || CONTROL GP -BUCKET
$917.52

23 Sep 2018
Caterpillar Lever Assy 5V3787 New
$1,019.60

25 Apr 2019
Caterpillar Lever Assy 5V3787 New
Number on catalog scheme: None
 
  For full view, you need register

Compatible equipment models: 5V3787:

WHEEL LOADER  966C   Caterpillar

Information:

Engines:
G3606 (S/N: 3XF)
G3608 (S/N: 4WF)
G3612 (S/N: 1YG)
G3616 (S/N: 4CG)
Description of Change: A new pressure relief valve assembly is used in the Hydrax system. The new pressure relief valve assembly will reduce the level of hydraulic fluid pressure fluctuations at normal operating conditions. High frequency pressure fluctuations can cause premature failure of the 140-9669 Switch (Hydrax system pressure switch). The new pressure relief valve assembly includes a serviceable relief valve. The relief valve in the former pressure relief valve assembly was not available for parts service. The serviceable relief valve can be used to replace the relief valve in the former pressure relief valve assembly.Adaptable To: The new 176-3586 Relief Valve (pressure relief valve assembly) is a direct replacement for the former 114-9206 Valve (pressure relief valve assembly). The former pressure relief valve assembly is cancelled. The new pressure relief valve assembly includes one 2M-9780 O-Ring Seal and one 5E-4852 Relief Valve. See the illustration.
Illustration 1 g00705644
Location of the 2M-9780 O-Ring Seal (2) and5E-4852 Relief Valve (1) in the new 176-3586 Relief Valve (pressure relief valve assembly).The 5E-4852 Relief Valve (1) can also be used to replace the relief valve in the former 114-9206 Valve (pressure relief valve assembly).Procedure To Install And Adjust The 5E-4852 Relief Valve
The Hydrax system should function properly when the Hydrax system hydraulic pressure is between 1448 to 1724 kPa (210 to 250 psi) at normal operating temperature. When you install the 5E-4852 Relief Valve, the Hydrax system hydraulic pressure should initially be set at 1448 kPa (210 psi). If this pressure is too low, a 456-04 Fault Code can occur at start-up. Increase the pressure setting until the 456-04 Fault Code is eliminated. The Hydrax system should operate normally with the system pressure at 1724 kPa (250 psi) or below 1724 kPa (250 psi).Note: If the Hydrax system hydraulic pressure must be set higher than 1724 kPa (250 psi) to eliminate the 456-04 Fault Code, there could be a problem with the system pressure gauge or with the 140-9669 Switch (Hydrax system pressure switch). If there is a history of Hydrax system pressure switch failures, install a new 140-9669 Switch (Hydrax system pressure switch) when the 5E-4852 Relief Valve is installed.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.
Shut down the engine.
Remove the pressure relief valve from the pressure relief valve housing.
Install a new 2M-9780 O-Ring Seal on the new 5E-4852 Relief Valve. Install the new relief valve in the pressure relief valve housing.
Remove the protective cap that is above the pressure setting screw on the new pressure relief valve. Loosen the locknut on the pressure setting screw.
Install a pressure gauge that can accurately display the Hydrax system hydraulic pressure. The Hydrax system hydraulic pressure should be around 1724 kPa (250 psi).
Start the engine. Run the engine until the Hydrax system hydraulic fluid is at normal operating temperature.
Use the pressure setting screw on the new pressure relief valve to

Caterpillar parts catalog:

Caterpillar parts catalog
966C WHEEL LOADER 30K02369-UP (MACHINE) POWERED BY 3306 ENGINE
966C WHEEL LOADER 18B01266-UP (MACHINE) POWERED BY 3306 ENGINE
966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE
966C WHEEL LOADER / POWER SHIFT / 18B00200-01265 (MACHINE) POWERED BY 3306 ENGINE


Parts lever Caterpillar catalog:

4M1853 LEVER AS-SHIFT
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
6K7382 LEVER
518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
6K3041 LEVER
814, 815, 920, 930, 950, 966C
5K0673 LEVER ASSEM.
814, 814S, 950, 966C
4V5344 LEVER
824C, 826C, 980C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.