7K2581 LEVER (FRONT R.H.) Caterpillar parts
950
Rating:
Alternative (cross code) number:
CA7K2581
7K-2581
7K2581
CA7K2581
7K-2581
7K2581
Weight: 84 pounds 38 kg.
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$510.67
25 Aug 2022
Amazon.com
7K2581 Lever - Fits: 950
GEN Compatible Models - 950 || Related Items - 1D4569 1K6872 3B8488 7K9343 || Interchange - 4K1743 || control Gp
GEN Compatible Models - 950 || Related Items - 1D4569 1K6872 3B8488 7K9343 || Interchange - 4K1743 || control Gp
$464.77
07 Jul 2022
Amazon.com
7K2581 Lever - Fits: 950
GEN Compatible Models - 950 || Related Items - 1D4569 1K6872 3B8488 7K9343 || Interchange - 4K1743 || control Gp
GEN Compatible Models - 950 || Related Items - 1D4569 1K6872 3B8488 7K9343 || Interchange - 4K1743 || control Gp
Compatible equipment models: 7K2581:
Information:
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Tests For The Air Inlet Heater
Illustration 1 g00659338
Right side of the engine
(1) Air inlet heater
(2) Fuel supply line
(3) Fuel transfer pump
Illustration 2 g00538494
(4) Electrical connection
(5) Fuel inlet
(6) Ball valve
(7) Valve holder
(8) Wire coil
(9) Ignition coilThe air inlet heater (1) is located in the air inlet manifold on the right side of the engine.Basic Operation
The air inlet heater frequently appears to leak because the ignition coil (9) is wet. The air inlet heater may be wet because the diesel fuel does not burn completely. This condition is normal. This condition does not indicate that the ball valve (6) has fuel leakage. If a leak is suspected, perform the leakage test.Check the heater operation by determining if the inlet manifold is warm to the touch near the heater after approximately 10 seconds of operation. The inlet manifold should be warm.Inspect the fuel tank and the fuel supply line (2) to the air inlet heater for restrictions and leakage of fuel.Check the fuel shutoff valve for correct operation. A poor seal on the fuel shutoff valve can cause air to enter the system which will cause extra cranking of the engine before starting. Be sure that all fuel connections are not leaking air.Make sure that the battery condition and the battery charge are satisfactory. Make sure that all electrical connections are tight. The electrical system can have reduced voltage if the following conditions exist:
A discharged battery
A loose connectionReduced voltage may cause slow cranking of the electric starting motor and failure of the heater unit to be activated.
If operated for a long period of time, The air inlet heater can create excessive heat. Excessive heat can damage the air inlet heater.
Leak Test For The Air Inlet Heater On The Engine
Use the following procedure to test for a leak in the air inlet heater.
Disconnect the fuel supply line (2) and the electrical connection on the air inlet heater. Be sure that the electrical connector is insulated from contact with metal engine components. Remove the air inlet heater from the manifold. Place a suitable plug in the manifold to prevent debris from entering the air inlet manifold.
Connect the fuel supply line to the air inlet heater. Loosely tighten the connection fitting. Operate the priming lever of the fuel transfer pump until only fuel which is free of air flows from the connection. Tighten the connection fitting.
Work carefully around an engine that is running. Engine parts that are hot, or parts that are moving, can cause personal injury.
Start the engine and operate the engine
Caterpillar parts catalog:
Parts lever Caterpillar catalog:
6K7382
LEVER
518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
6K3041
LEVER
814, 815, 920, 930, 950, 966C
814, 815, 920, 930, 950, 966C
6K3028
LEVER
814, 815, 950, 966C, 980B
814, 815, 950, 966C, 980B
4K8454
LEVER
950, 966C, 980, 980B
950, 966C, 980, 980B
5J0995
LEVER
814, 950, 966C, 966R, 980, 980B
814, 950, 966C, 966R, 980, 980B
5J7671
LEVER
814, 950, 966C, 966R, 980, 980B
814, 950, 966C, 966R, 980, 980B
8K8053
LEVER
950
950
6K3918
LEVER ASSEM.
814, 950, 966C, 980, 980B, 988
814, 950, 966C, 980, 980B, 988
7K1832
LEVER
814, 950, 966C, 980B, 988
814, 950, 966C, 980B, 988
5C6751
LEVER
950
950
4K8477
LEVER
950, 966C
950, 966C
5J4511
LEVER ASSEM.
980, 980B
980, 980B
7K3101
LEVER
988, 992
988, 992
4K0932
LEVER
824S, 988
824S, 988
8K8434
LEVER
815, 816, 966C, 992
815, 816, 966C, 992
8K5169
LEVER
992
992
7K1832
LEVER
814, 950, 966C, 980B, 988
814, 950, 966C, 980B, 988
6K3918
LEVER ASSEM.
814, 950, 966C, 980, 980B, 988
814, 950, 966C, 980, 980B, 988
8K8053
LEVER
950
950