8V1624 LEVER Caterpillar parts
814B, 814F, 815F, 816F, 916, 926, 926A, 936, 936F, 950B, 950B/950E, 966D, 966F, 966F II, 970F, CS-643, G926, G936, IT18, IT18B, IT28, IT28B
Rating:
Alternative (cross code) number:
CA8V1624
8V-1624
8V1624
CA8V1624
8V-1624
8V1624
Weight: 0.50 pounds 0 kg.
Information:
ARM OFFSET DIMENSION
6
mm
AXIS CENTERLINE TO CENTERLINE DIMENSION
36
mm
AXIS OFFSET DIMENSION
0
mm
FULCRUM HOLE DIAMETER
0
mm
FULCRUM PITCH DIAMETER
15.367
mm
LINKAGE HOLE DIAMETER
5.2
mm
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Related part:
8V1624
LEVER-YM
2992019
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 8V1624:
Information:
Remove & Install Crankshaft Main Bearings
Start By:a. remove oil pan 1. Remove bolts (1) that hold main bearing cap (2) in place. Remove main cap (2).2. Remove the bearing half from the cap.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both the crankshaft and cylinder block.
3. Remove the upper half of main bearings (3) as follows:a. Turn the crankshaft until Tool (A) can be installed in the crankshaft journal. Install Tool (A).b. Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.c. Check the condition of the bearings. See "Guideline For Reusable Parts", "Main And Connecting Rod Bearings", Form No. SEBF8009 and SEBD0531. The following steps are for the installation of the crankshaft main bearings. Put clean engine oil on the main bearings for the assembly. Also, be sure the tabs on the back side of the main bearings fit in the grooves of the main bearing caps and cylinder block.
Ensure that the bearings are installed in the correct locations. Two different part numbers are used in quantities of three and four. The part number having the quantity of four is to be installed on crankshaft main bearings 2, 3, 5 and 6. The part number having the quantity of three is to be installed on crankshaft bearing 1, 4 and 7.
4. Clean the surfaces in the cylinder block for the main bearings. Use Tool (A), and install new upper halves of main bearing (bearings with the oil hole) in the cylinder block. Do not put oil on the back of the bearing.5. Clean the surface of the main bearing caps for the main bearings. Install the new lower halves of the main bearings in the main caps. Do not put oil on the back of the bearing.
Main bearing caps should be installed with the part number towards the right side. Caps are to be identified by stamped numbers 1 thru 7 located on the bottom unmachined surface.
6. Put main bearing caps (2) in position on the cylinder block. Put clean engine oil or 1P0808 All-Purpose Lubricant on the bolt threads and the washer face; then install the bolts. Tighten the bolts on the side where the main bearing tabs are located to a torque of 95 5 N m (70 4 lb ft). Tighten the bolts on the opposite side to a torque of 95 5 N m (70 4 lb ft).7. Put a mark on each bolt head and the bearing caps. Turn the bolts that are opposite the main bearing tabs an additional 90 5 degrees turn. Then turn the bolts on the side where the main bearing tabs are located an additional 90 5 degrees turn.
Typical Example8. Check the end play of the crankshaft with a dial indicator and magnetic base. The end play must be 0.10 to
Start By:a. remove oil pan 1. Remove bolts (1) that hold main bearing cap (2) in place. Remove main cap (2).2. Remove the bearing half from the cap.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both the crankshaft and cylinder block.
3. Remove the upper half of main bearings (3) as follows:a. Turn the crankshaft until Tool (A) can be installed in the crankshaft journal. Install Tool (A).b. Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.c. Check the condition of the bearings. See "Guideline For Reusable Parts", "Main And Connecting Rod Bearings", Form No. SEBF8009 and SEBD0531. The following steps are for the installation of the crankshaft main bearings. Put clean engine oil on the main bearings for the assembly. Also, be sure the tabs on the back side of the main bearings fit in the grooves of the main bearing caps and cylinder block.
Ensure that the bearings are installed in the correct locations. Two different part numbers are used in quantities of three and four. The part number having the quantity of four is to be installed on crankshaft main bearings 2, 3, 5 and 6. The part number having the quantity of three is to be installed on crankshaft bearing 1, 4 and 7.
4. Clean the surfaces in the cylinder block for the main bearings. Use Tool (A), and install new upper halves of main bearing (bearings with the oil hole) in the cylinder block. Do not put oil on the back of the bearing.5. Clean the surface of the main bearing caps for the main bearings. Install the new lower halves of the main bearings in the main caps. Do not put oil on the back of the bearing.
Main bearing caps should be installed with the part number towards the right side. Caps are to be identified by stamped numbers 1 thru 7 located on the bottom unmachined surface.
6. Put main bearing caps (2) in position on the cylinder block. Put clean engine oil or 1P0808 All-Purpose Lubricant on the bolt threads and the washer face; then install the bolts. Tighten the bolts on the side where the main bearing tabs are located to a torque of 95 5 N m (70 4 lb ft). Tighten the bolts on the opposite side to a torque of 95 5 N m (70 4 lb ft).7. Put a mark on each bolt head and the bearing caps. Turn the bolts that are opposite the main bearing tabs an additional 90 5 degrees turn. Then turn the bolts on the side where the main bearing tabs are located an additional 90 5 degrees turn.
Typical Example8. Check the end play of the crankshaft with a dial indicator and magnetic base. The end play must be 0.10 to
Caterpillar parts catalog:
Parts lever Caterpillar catalog:
4T1022
LEVER GP
446, 446B, 446D, 926, 926A, 936, 936F, D6H, D6H II, D6H XL, D6H XR, D9R, G926, G936, IT28, IT28B
446, 446B, 446D, 926, 926A, 936, 936F, D6H, D6H II, D6H XL, D6H XR, D9R, G926, G936, IT28, IT28B
4M1853
LEVER AS-SHIFT
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
4T0998
LEVER
446B, 446D, 916, 936F, D5C III, D6H, D6H XL, D6H XR, D7H, D8N, D8R, D9R, G936, IT18B, IT28
446B, 446D, 916, 936F, D5C III, D6H, D6H XL, D6H XR, D7H, D8N, D8R, D9R, G936, IT18B, IT28
9M7394
LEVER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 16, 160G, 160H, 160H ES, 160H N...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 16, 160G, 160H, 160H ES, 160H N...
8M6770
LEVER-GOVERNOR CONTROL
561C, 561D, 814B, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR
561C, 561D, 814B, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR
8V1613
LEVER
814B, 814F, 815F, 816F, 926, 938F, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, 980C, 980F, 988B, 988F, 992C, 992D, 994, D5B, G936
814B, 814F, 815F, 816F, 926, 938F, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, 980C, 980F, 988B, 988F, 992C, 992D, 994, D5B, G936
4E3456
LEVER AS
814B, 815B, 826C, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F
814B, 815B, 826C, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F
7V1881
LEVER
814B, 814F, 815B, 815F, 816F, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F
814B, 814F, 815B, 815F, 816F, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F
4E3119
LEVER AS
966D, 966F, 966F II, 970F
966D, 966F, 966F II, 970F
4E4449
LEVER AS
814B, 815B, 825C, 834B, 836
814B, 815B, 825C, 834B, 836
3V8040
LEVER
814B, 824C, 834B, 836
814B, 824C, 834B, 836
9V2170
LEVER
814B
814B
9V1787
LEVER
916, 926, 936, 936F, CS-643, G936, IT28
916, 926, 936, 936F, CS-643, G936, IT28
7V3647
LEVER & BEARING AS
936, 936F, G936
936, 936F, G936
8V2101
LEVER
916, 926, 936, 936F, CS-643, G936, IT28, IT28B
916, 926, 936, 936F, CS-643, G936, IT28, IT28B
8V7292
LEVER ASSEM.
920, 930
920, 930
8V7294
LEVER ASSEM.
920, 930
920, 930
5V3646
LEVER
920
920
9V3113
LEVER ASSEM.
920, 930
920, 930
5T2027
LEVER AS
637D
637D
9V1393
LEVER (KICKOUT)
916, 926, 936, 936F, G936
916, 926, 936, 936F, G936
9V1363
LEVER
916, 926, 936, 936F, G936
916, 926, 936, 936F, G936
9V1030
LEVER
916, 926, 936, 936F, G936
916, 926, 936, 936F, G936
8V2760
LEVER (3RD. VALVE)
916, 926, 926A, 936, G936, IT28
916, 926, 926A, 936, G936, IT28