LEVER AS 9R2017 - Caterpillar

"Machine Working Engine Low Idle Speed Configuration"
The "Machine Working Engine Low Idle Speed Configuration" is the engine rpm for the machine during normal operation. The engine idle rpm may be set for work mode in order to meet the application requirements."Machine Hibernating Engine Low Idle Speed Configuration"
The machine hibernate engine low idle speed provides lower fuel consumption and reduced sound and emissions levels in applications with considerable idle time. The hibernate mode is engaged after ten seconds and the following conditions are met:
The transmission is in neutral.
The parking brake is engaged.
The implement hydraulic levers are in neutral positions.
The throttle pedal is not depressed for greater than five percent.
The fan current is greater than 0.8 amp and the engine temperature is greater than 50° C (122° F)The "Machine Working Engine Low Idle Speed Configuration" rpm will return if one of the following conditions are met:
The parking brake is released.
A directional shift occurs.
A hydraulic lever is moved.
The governor pedal is pushed.The machine hibernating engine low idle speed configuration can be set in the range of 600 to 825 rpm."Engine Idle Shutdown Enable Status"
This feature enables the ECM to shut down the engine after the Engine Idle Shutdown Delay Time has expired."Engine Idle Shutdown Delay Time"
The delay time is the amount of time that the engine is allowed to idle prior to shutdown if the machine is not being operated.Parameter Table
Table 1
Customer Specified Parameters
Parameter Available Range or Options Default Required Password
"Product ID" eight characters blank none
"Equipment ID" 17 characters blank none
"Engine Serial Number" eight characters blank none
"FLS" -128 to +127 0 Factory
"FTS" -128 to +127 0 Factory
"Engine Fan Control" "Enabled" or "Disabled" "Enabled" none
"Engine Fan Reversing Feature" "Enabled" or "Disabled" "Enabled" none
"Engine Fan Purge Cycle Interval" 3 to 60 minutes none
"Security System Immobilizer Installation Status" "Installed" or "Not installed" "Not installed" Factory
"Ether Solenoid Configuration" "Enabled" or "Disabled" "Disabled" none
"Low System Battery Voltage Elevated Idle" "Enabled" or "Disabled" "Enabled" none
"Engine Warm-up Elevated Idle Feature Enable Status" "Enabled" or "Disabled" Enabled none
"Machine Working Engine Low Idle Speed Configuration" 650 to 1000 rpm 800 rpm (980H)
825 rpm (other machines) none
"Machine Hibernating Engine Low Idle Speed Configuration" 600 to 825 rpm 600 rpm none
"Engine Idle Shutdown Enable Status" Enabled
Disabled Enabled none
"Engine Idle Shutdown Delay Time" 3 to 60 minutes 5 minutes none Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 2
Settings for the Configuration Parameters
"Product ID"
"Equipment ID"
"Engine Serial Number"
"ECM Serial Number"
"Personality Module Part Number"
"Personality Module Release Date"
"Personality Module Description"
"FLS"
"FTS"
"Engine Fan Control"
"Engine Fan Reversing Feature"
"Engine Fan Purge Cycle Interval"
"Security System Immobilizer Installation Status"
"Ether Solenoid Configuration"
"Low System Battery Voltage Elevated Idle"
"Engine Warm-up Elevated Idle Feature Enable Status"
"Machine Working Engine Low Idle Speed Configuration"
"Machine Hibernating Engine Low Idle Speed Configuration"
"Engine Idle Shutdown Enable Status"
"Engine Idle Shutdown Delay Time"
"Total Tattletale"
Engine Serial Number
Full Load Setting
(for new ECM)
Full Torque Setting
(for new ECM)
Injector Code (1)
Injector Code (2)
Injector Code (3)
Injector Code (4)
Injector Code (5)
Injector Code (6) Note: Compare the FLS and the FTS from the ECM with the values that are listed on the engine information plate. Only