8N4353 LINE ASSEM. (No. 3) Caterpillar parts
D4E
Rating:
Alternative (cross code) number:
CA8N4353
8N-4353
8N4353
CA8N4353
8N-4353
8N4353
Weight: 0.50 pounds 0 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 8N4353:
Number on catalog scheme:
3
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs 1/2 inch - UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1).
Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered on ring gear teeth will ensure the correct engagement of the starting motor.
Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
Illustration 2 g01336668
Typical example
Install a suitable lifting device on flywheel (1). The flywheel can weigh 71 kg (156 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
Install bolts (4) to flywheel (1).
Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs 1/2 inch - UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1).
Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered on ring gear teeth will ensure the correct engagement of the starting motor.
Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
Illustration 2 g01336668
Typical example
Install a suitable lifting device on flywheel (1). The flywheel can weigh 71 kg (156 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
Install bolts (4) to flywheel (1).
Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts line Caterpillar catalog:
621R, 966C, D5B, D7G
621R, 941, 955K, 955L, 966C, D5B, D7G
4P8603
LINE AS-FUEL INJ
627E, 637E, D7H
627E, 637E, D7H
4P8601
LINE AS-FUEL INJ
627E, 637E, D7H
627E, 637E, D7H
4P8602
LINE AS-FUEL INJ
627E, 637E, D7H
627E, 637E, D7H
4P8604
LINE AS-FUEL INJ
621E, 627E, 637E, D7H
621E, 627E, 637E, D7H
