LINER-CYLINDER 1111656 - Caterpillar

1111656 LINER-CYLINDER Caterpillar parts 3606, 3608, 3612, 3616

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1111656
111-1656
1111656

Weight: 222 pounds 100 kg.

Buy LINER-CYLINDER 1111656 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET-MILITARY, MARINE ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

22 Jan 2019

Unbrako: Unbrako

Unbrako 1111656 Alloy Steel Socket Cap Screw, Black Oxide Finish, Knurled Socket Cap Head, Hex Socket Drive, Meets ASME B18.3, Right Hand Threads, 3/4"-10 Thread Size, 3-1/4" Length, Partially Threaded (Pack of 25)
Alloy steel is often used in applications where strength is the primary consideration, and black oxide finish offers mild corrosion resistance and lubricity || Socket cap head is round with a flat top and a high profile that provides high strength || Knurling on the head enhances grip for hand-turning || Hex socket drive has a hexagonal slot that turns using an Allen key driver, permitting more compact spacing than a hex head cap screw || Meets ASME B18.3 specifications

Show more prices Caterpillar parts

Number on catalog scheme: 7

Caterpillar 1111656 Parts scheme LINER-CYLINDER

For full view, you need register

Compatible equipment models: 1111656:

GEN SET-MILITARY 3608

MARINE ENGINE 3606 3608 3612 3616 Caterpillar

Information:

Test Procedure
System Operation
The SLC 5/04 - 5/05 diagnostic indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.The "FLT" LED is illuminated and the outputs of the controller are de-energized. The power to a chassis is lost.The red "FLT" LED is illuminated. There is a fatal error. A fatal error indicates that the processor is not communicating.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.The green "RS232" LED is illuminated in the DH+ mode. The communications active bit (S:17) is set in the "System Status" file. The processor is communicating on the network.The green "RS232" LED is flashing in the DH+ mode. The processor cannot establish communication because there are no active nodes on the network.The "RS232" LED is extinguished in the DH+ mode. A fatal error is present.
Illustration 1 g00766228
Diagram of the LED indicators
Illustration 2 g00766223
Functional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04 - 5/05.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the line voltage.
Reconnect the power supply.
Measure the line voltage at the terminals.
Verify the voltage of the power supply. The power supply voltage should be measured between 21.0 VDC and 28.0 VDC.The results of the preceding procedure are in the following list:
The line voltage is in the range. Proceed to 3.
The line voltage is out of the range. Refer to Troubleshooting, "System Power". Stop.
Cycle the power.
Secure power to the PLC.
Energize the PLC.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Refer to Maintenance Procedure, "Processor - Replace". Stop.