1904705 LINER AS-CAB Caterpillar parts
914G, 924G, 924GZ, 928G, 938G, 938G II, CP-433E, CP-44, CP-56, CP-573E, CP-64, CP-663E, CP-76, CS-423E, CS-433E, CS-44, CS-531D, CS-533D, CS-56, CS-563D, CS-563E, CS-573D, CS-583D, CS-583E, CS-64, CS-...
Rating:
Alternative (cross code) number:
CA1904705
190-4705
1904705
CA1904705
190-4705
1904705
Weight: 15 pounds 7 kg.
COMPACT WHEEL LOADER, WHEEL LOADER,
This part in 7 request:
Show.
This information for suppliers only!
2025-05-13
2023-10-20
2023-07-31
2023-07-31
2021-06-08
2019-11-13
2019-10-08
Compatible equipment models: 1904705:
Cat SIS web machinery list:
Information:
Which Generate This Code:This fault is indicated when the ECM detects a short to ground. The short is in the path from the control to the solenoid. If the solenoid for the forward direction has a short to ground, the ECM shifts the machine to neutral. The forward direction is not available. Connector contact 31 relates to this fault.Note: The following steps may create other indicated faults. Clear these faults when the original fault is corrected.Test Step 1. CHECK THE SOLENOID VALVE
Turn the start switch to the OFF position.
Disconnect the faulty solenoid from the machine harness.
At the solenoid, measure the resistance from contact 1 to contact 2.Note: This procedure causes the ECM to indicate an open circuit for this solenoid. Clear this code from the control after troubleshooting.Expected Result:The resistance should be 20 ohms to 25 ohms.Results:
NO - The resistance is not 20 ohms to 25 ohms.Repair: The solenoid is faulty. Replace the solenoid. Stop.
YES - The resistance is 20 ohms to 25 ohms. Proceed to test step 2.Test Step 2. CHECK THE HARNESS
Reconnect all harness connectors.
Disconnect the harness connector from the control.
Measure the resistance from the faulty solenoid to contact 39.
Expected Result:The resistance measurement should be 20 ohms to 25 ohms.Results:
NO - There is a short circuit to ground in the machine harness.Repair: Fix the harness or replace the harness. Stop.
YES - The resistance is 20 ohms to 25 ohms. Proceed to step 3.Test Step 3. CHECK IF THE FAULT REMAINS
Turn the start switch to the OFF position.
Inspect the harness connectors.
Reconnect the harness connectors.
Turn the start switch to the ON position.
Enter the service mode.
Operate the machine.
Check if the same fault is active.Results:
YES - The fault has not been corrected. Repair: Perform the previous steps. If the cause of the fault is not found, replace the control. Stop.
NO - The fault does not exist at this time. The fault was probably caused by a poor electrical connection. Resume normal machine operation. Stop.
Turn the start switch to the OFF position.
Disconnect the faulty solenoid from the machine harness.
At the solenoid, measure the resistance from contact 1 to contact 2.Note: This procedure causes the ECM to indicate an open circuit for this solenoid. Clear this code from the control after troubleshooting.Expected Result:The resistance should be 20 ohms to 25 ohms.Results:
NO - The resistance is not 20 ohms to 25 ohms.Repair: The solenoid is faulty. Replace the solenoid. Stop.
YES - The resistance is 20 ohms to 25 ohms. Proceed to test step 2.Test Step 2. CHECK THE HARNESS
Reconnect all harness connectors.
Disconnect the harness connector from the control.
Measure the resistance from the faulty solenoid to contact 39.
Expected Result:The resistance measurement should be 20 ohms to 25 ohms.Results:
NO - There is a short circuit to ground in the machine harness.Repair: Fix the harness or replace the harness. Stop.
YES - The resistance is 20 ohms to 25 ohms. Proceed to step 3.Test Step 3. CHECK IF THE FAULT REMAINS
Turn the start switch to the OFF position.
Inspect the harness connectors.
Reconnect the harness connectors.
Turn the start switch to the ON position.
Enter the service mode.
Operate the machine.
Check if the same fault is active.Results:
YES - The fault has not been corrected. Repair: Perform the previous steps. If the cause of the fault is not found, replace the control. Stop.
NO - The fault does not exist at this time. The fault was probably caused by a poor electrical connection. Resume normal machine operation. Stop.
Parts liner Caterpillar catalog:
1111815
LINER
3054, 3054B, 3056, 3056E, 312B L, 312C, 315B L, 416C, 416D, 420D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908, 914G, 924G, 924GZ, 930G, AP-655C, AP-800C, BB-7...
3054, 3054B, 3056, 3056E, 312B L, 312C, 315B L, 416C, 416D, 420D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908, 914G, 924G, 924GZ, 930G, AP-655C, AP-800C, BB-7...
1188028
LINER
914G, IT14G
914G, IT14G
1117859
LINER AS-CAB
910G, 914G, 924G, 924GZ, 928G, 938G, CS-423E, CS-531D, CS-533D, IT14G, IT28G, IT38G
910G, 914G, 924G, 924GZ, 928G, 938G, CS-423E, CS-531D, CS-533D, IT14G, IT28G, IT38G
1261034
LINER AS-CAB
914G, 924G, 924GZ, 924H, 924HZ, 928G, 928HZ, 930G, 938G, 938G II, IT14G, IT14G2, IT28G, IT38G, IT38G II
914G, 924G, 924GZ, 924H, 924HZ, 928G, 928HZ, 930G, 938G, 938G II, IT14G, IT14G2, IT28G, IT38G, IT38G II
1362517
LINER
938G
938G
1985931
LINER
938G, 938H, 950G II, 950H, 962G II, 962H, PW2503/7
938G, 938H, 950G II, 950H, 962G II, 962H, PW2503/7
1985932
LINER
938G, 938H, 950G II, 950H, 962G II, 962H, PW2503/7
938G, 938H, 950G II, 950H, 962G II, 962H, PW2503/7
1740563
LINER AS-CAB
924G, 924GZ, 924H, 924HZ, 938G, 938G II
924G, 924GZ, 924H, 924HZ, 938G, 938G II
2509720
LINER AS-CAB
938G II, 938H, IT38G II, IT38H
938G II, 938H, IT38G II, IT38H
2324712
LINER AS-CAB
938G II, IT38G II
938G II, IT38G II
1966977
LINER
CS-531D, CS-533D
CS-531D, CS-533D
1244702
LINER AS
924F, 938F, 950F II, 960F
924F, 938F, 950F II, 960F
1244701
LINER AS-CAB
924F, 938F, 950F II, 960F
924F, 938F, 950F II, 960F
1261034
LINER AS-CAB
914G, 924G, 924GZ, 924H, 924HZ, 928G, 928HZ, 930G, 938G, 938G II, IT14G, IT14G2, IT28G, IT38G, IT38G II
914G, 924G, 924GZ, 924H, 924HZ, 928G, 928HZ, 930G, 938G, 938G II, IT14G, IT14G2, IT28G, IT38G, IT38G II
1117859
LINER AS-CAB
910G, 914G, 924G, 924GZ, 928G, 938G, CS-423E, CS-531D, CS-533D, IT14G, IT28G, IT38G
910G, 914G, 924G, 924GZ, 928G, 938G, CS-423E, CS-531D, CS-533D, IT14G, IT28G, IT38G
1188028
LINER
914G, IT14G
914G, IT14G
1037300
LINER
918F, 924F, IT24F
918F, 924F, IT24F
1502684
LINER-LH
631E, 631G, 637E, 637G
631E, 631G, 637E, 637G
1502683
LINER-RH
631E, 631G, 637E, 637G
631E, 631G, 637E, 637G
1502682
LINER
631E, 631G, 637E, 637G
631E, 631G, 637E, 637G
1502680
LINER
631E, 631G, 637E, 637G
631E, 631G, 637E, 637G
1502673
LINER
631E, 631G, 637E, 637G
631E, 631G, 637E, 637G
1502672
LINER
631E, 631G, 637E, 637G
631E, 631G, 637E, 637G