LINES GP-FUEL 1800607 - Caterpillar

1800607 LINES GP-FUEL Caterpillar parts 966G II, 972G II

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1800607
180-0607
1800607

Buy LINES GP-FUEL 1800607 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

BECKARNLEY 180-0607 Crank Position Sensor

$330.58

02 Jun 2020
1.16[0.45] Pounds
-: -

BECKARNLEY 180-0607 Crank Position Sensor
Matches OE form, fit, and function including strength of the magnet || Includes corrosion resistant terminals and coatings || Premium construction for durability || Designed for harsh underhood conditions || Application specific to ensure a correct fit for your vehicle

Polaris 2014-2016 Rzr Hose 28In 1800607 New Oem

$108.99

25 Feb 2020

-: -

Polaris 2014-2016 Rzr Hose 28In 1800607 New Oem
New OEM Polaris Hose 28In || OEM Part Number: 1800607 || Item only fits specific models listed. The picture could be generic. || Message us with VIN/HULL for fast fitment verification.

For full view, you need register

Compatible equipment models: 1800607:

WHEEL LOADER 966G II 972G II Caterpillar

Information:

TYPE="LEVEL" DEPTH="1" @@@-->Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6640 Sealant 1
B - Guide Stud
M16 by 50 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01616335
Ensure that engine oil pan (5) is clean and free from damage. Clean isolating screws (6) and isolating screws (7). Inspect the isolating screws for deterioration or damage. If necessary, replace the isolating screws. Ensure that the gasket surface of the isolating frame is clean. Note: The isolating screws must be replaced as a complete set in order to ensure even clamping of the engine oil pan.
Position a new gasket (4) onto the engine oil pan (5).
Illustration 2 g01340724
(Z) Position of short isolating screws.
Install isolating screws (5) and isolating screws (6) to the engine oil pan. Do not install the isolating screws to the large holes at Positions (X) in the engine oil pan. Note: The isolating screws are held captive by the gasket.
Install the assembly of the engine oil pan to the isolating frame. Tighten the isolating screws to a torque of 22 N m (16 lb ft). Tighten the isolating screws in the sequence that is shown in Illustration 2.
Illustration 3 g01340725
Install the four remaining isolating screws. Tighten the isolating screws to a torque of 22 N m (16 lb ft). Tighten the isolating screws in the sequence that is shown in Illustration 3.
Illustration 4 g01617554
Engines that are keel cooled and sea water cooled install Tooling (B) to the engine mountings.
Use a suitable hoist to lower the front of the engine onto the base frame. Remove Tooling (B) from the engine mountings. Install bolts (8). Tighten bolts to a torque of 190 N m (140 lb ft). Engines with a radiator cooled systems. Tighten nuts and bolts for the engine mounting and the generator mounting to a torque of 190 N m (140 lb ft).
Illustration 5 g01340605
Typical example
If necessary, follow Step 8.a through Step 8.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to tube assembly (2).
Apply Tooling (A) to nut (1). Install the tube assembly to the engine oil pan.
Tighten the nut (1) to a torque of 18 N m (13 lb ft). Install the dipstick (not shown). Note: Ensure that the orientation of the tube assembly is correct.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the procedure.