AVSPARE.COM
parts catalog

LINES GP-PILOT 2214897 - Caterpillar


2214897 LINES GP-PILOT Caterpillar parts 322C, 322C FM
Rating:
86
Alternative (cross code) number:
CA2214897
221-4897
2214897
Caterpillar 2214897 LINES GP-PILOT

Buy LINES GP-PILOT 2214897 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, LOGGER,

Compatible equipment models: 2214897:

EXCAVATOR  322C FM  
LOGGER  322C   Caterpillar
  For full view, you need register

Information:


Table 1
Required Tools    
Part Number    Description    Required Amount    
198-4240     Digital Pressure Indicator     1    
9T-6865     Adapter Plug     1    
5P-2937     O-Ring Adapter     1    
6V-3966     Fitting As     1    
Illustration 1 g00692584
Rear of Tractor (1) Plug in elbow
Illustration 2 g00987132
View of Ejector Cylinder (2) Ejector cylinder (3) Ejector valve (speed change)
Illustration 3 g00987134
Section View of Ejector Valve (Speed Change) (4) Spring (5) Cover (6) Shims (7) Spring (inside) (8) Spring (outside) (9) BoltsNote: The bowl must be full in order to test the pressure of the speed change when the load in the bowl is ejected.
Operate the machine until the hydraulic oil reaches normal operating temperature.
Stop the machine on a hard, level surface. Move the transmission control lever to NEUTRAL. Lower the bowl. Stop the engine. Engage the parking brake.
Remove plug (1) .
Assemble the following components and connect to the open port: 9T-6865 Adapter Plug, 5P-2937 O-Ring Adapter and 6V-3966 Fitting As .
Connect 198-4240 Digital Pressure Indicator to the 6V-3966 Fitting As .
Start the engine. Run the engine at 1000 RPM.
Move the ejector control lever slowly toward EJECT position and observe the pressure gauge. The reading on the pressure gauge should be 12765 170 kPa (1850 25 psi).
As the load flows out of the bowl, the reading on the pressure gauge will decrease. When the reading decreases to 6035 515 kPa (875 75 psi), the valve stem in the ejector valve will shift and the ejector will move faster.Note: If the control lever is held in EJECT position, the reading will increase to the relief valve pressure.
If the high pressure setting requires adjustment, continue to Step 10. If the high pressure setting is correct, continue to Step 16.
If it is necessary to change the high pressure setting of the ejector valve, stop the engine.
Remove four bolts (9). Remove cover (5) .Note: Shims (6), springs (7) and (8), a retainer and a valve stem can come out of the ejector valve when cover (6) is removed.
Remove shims (6) in order to decrease the high pressure setting of the ejector valve. Add shims (6) in order to increase the high pressure setting of the ejector valve. Refer to Table 2 for the pressure change of the shims.
Install shims (6), springs (7) and (8), the retainer and the valve stem.
Install cover (5) and four bolts (9) .
Repeat Steps 6 through 9.
Stop the engine. Remove all test equipment.
Install plug (1) .
Table 2
Chart for Shims    
Part Number     Thickness     Pressure Change for One Shim    
3J-2979    
1.52 0.15 mm (0.060 0.006 inch)    
415 kPa (60 psi)    

Caterpillar parts catalog:

Caterpillar parts catalog
CUSTOM PRODUCT SUPPORT LITERATURE FOR THE 322C LGP FOREST MA SLX00001-UP (MACHINE)
322C FOREST SWING MACHINES BPH00001-UP (MACHINE) POWERED BY 3126 Engine


Parts lines Caterpillar catalog:

1211729 LINES GP-GREASE
322 L, 322B, 322B L, 322C, 322C FM, 324D, 324D L, 324E, 324E L, 324E LN, 325, 325 L, 325B L, 325C, 325C L, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN
1132126 LINES GP - GREASE
322, 322 FM L, 322B L, 322C
2460716 LINES GP-WINDOW WASHER
322C FM, 324D FM LL, 325C FM, 325D FM, 330C FM, 330D FM
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.