2469318 LINES GP-BUCKET Caterpillar parts
416E
Rating:
Alternative (cross code) number:
CA2469318
246-9318
2469318
CA2469318
246-9318
2469318
BACKHOE LOADER,
Compatible equipment models: 2469318:
Information:
Installing the Warning Decal(s)
Two 8T2930 decals are included in the group:
Example of the 8T2930 decal installed close to the engine's 9L6531 Engine Information Plate.* Install one in a VISIBLE location in vehicle cab ... and* Install one in a VISIBLE location in engine compartment or on engine.Operating the Intake Manifold Heater
This portion of the instruction will explain the operation of the intakemanifold heater and a basic explanation of how it works.A few moments spent learning the sequential steps required to engage the system, and a reasonable knowledge of the components functions during cranking, will allow the operator to start the engine in a minimum amount of time.Procedures to Start the Engine
Switch on (RUN position) the main key operated switch:* The indicator light MUST light up and stay on for the duration of heating process.* This will start the (40 - 60 seconds) heater plug preheat mode. The heater plug will start to heat as soon as the switch is activated (RUN position). The heater plug will soon be too HOT to touch.The preheating process is voltage dependent, refer to the Corrective Action column in the Troubleshooting chart.* The preheating process will last 40 - 60 seconds (depending on the voltage).* Upon completion of the preheating process the pilot lamp will go out.* The engine can now be started.Start the Engine
The engine must be started:As soon as the engine starts:* The indicator light will light up again for the entire duration of the inlet manifold heating process.* Not later than 30 8 seconds AFTER the indicator light goes out ... and* The alternator MUST reach charging speed ... or* The oil pressure switch MUST close.If these two requirements are NOT met:* The intake manifold heating system will be switched OFF automatically.This happens when the alternator does not provide a signal to the D+ terminal of the ECU.If this occurs:To restart the engine the main key operated switch must now be:* Switched OFF for several seconds before attempting to start the engine.When the main switch is switched on (RUN position) again:* The pilot lamp will light up to indicate the start of the preheating process.The engine can be started after:* The pilot light goes out.After Engine Start
After the engine is started:* The engine speed must NOT be allowed to exceed low idle rpm for the duration of the intake manifold heating process.The heating cycle is completed as soon as:* The indicator light goes out.The duration of the intake manifold heating process is up to 6 minutes and is controlled automatically by the Electronic Control Unit (ECU).Intake Manifold Heater System Functional Check
Fuel Lines
Inspect all fuel supply/return lines, connections, and screw type fittings for fuel leakage.Replace/repair/tighten if required.Checking the System At Ambient Temperature
The system can be checked for correct operation at any temperature by:* Disconnecting the temperature sensor ... and* Performing the normal (cold start) engine starting procedures.The system can now be checked for correct operation even when the engine is at normal operating temperature.Refer to Operating the Intake Manifold Heater
Two 8T2930 decals are included in the group:
Example of the 8T2930 decal installed close to the engine's 9L6531 Engine Information Plate.* Install one in a VISIBLE location in vehicle cab ... and* Install one in a VISIBLE location in engine compartment or on engine.Operating the Intake Manifold Heater
This portion of the instruction will explain the operation of the intakemanifold heater and a basic explanation of how it works.A few moments spent learning the sequential steps required to engage the system, and a reasonable knowledge of the components functions during cranking, will allow the operator to start the engine in a minimum amount of time.Procedures to Start the Engine
Switch on (RUN position) the main key operated switch:* The indicator light MUST light up and stay on for the duration of heating process.* This will start the (40 - 60 seconds) heater plug preheat mode. The heater plug will start to heat as soon as the switch is activated (RUN position). The heater plug will soon be too HOT to touch.The preheating process is voltage dependent, refer to the Corrective Action column in the Troubleshooting chart.* The preheating process will last 40 - 60 seconds (depending on the voltage).* Upon completion of the preheating process the pilot lamp will go out.* The engine can now be started.Start the Engine
The engine must be started:As soon as the engine starts:* The indicator light will light up again for the entire duration of the inlet manifold heating process.* Not later than 30 8 seconds AFTER the indicator light goes out ... and* The alternator MUST reach charging speed ... or* The oil pressure switch MUST close.If these two requirements are NOT met:* The intake manifold heating system will be switched OFF automatically.This happens when the alternator does not provide a signal to the D+ terminal of the ECU.If this occurs:To restart the engine the main key operated switch must now be:* Switched OFF for several seconds before attempting to start the engine.When the main switch is switched on (RUN position) again:* The pilot lamp will light up to indicate the start of the preheating process.The engine can be started after:* The pilot light goes out.After Engine Start
After the engine is started:* The engine speed must NOT be allowed to exceed low idle rpm for the duration of the intake manifold heating process.The heating cycle is completed as soon as:* The indicator light goes out.The duration of the intake manifold heating process is up to 6 minutes and is controlled automatically by the Electronic Control Unit (ECU).Intake Manifold Heater System Functional Check
Fuel Lines
Inspect all fuel supply/return lines, connections, and screw type fittings for fuel leakage.Replace/repair/tighten if required.Checking the System At Ambient Temperature
The system can be checked for correct operation at any temperature by:* Disconnecting the temperature sensor ... and* Performing the normal (cold start) engine starting procedures.The system can now be checked for correct operation even when the engine is at normal operating temperature.Refer to Operating the Intake Manifold Heater
Caterpillar SIS machinery equipment:
Caterpillar SIS
416E Backhoe Loader Single Tilt Center Pivot SHA00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt Center Pivot SHA00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt Center Pivot SHA00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt Center Pivot CBD00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt Center Pivot CBD00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt Center Pivot CBD00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt Center Pivot CBD00001-UP (MACHINE) POWERED BY 3054C Engine »
246-9318
LINES GP-BUCKET
416E Single Tilt Backhoe Loader BWC00001-UP (MACHINE) POWERED BY C4.4 Engine »
246-9318
LINES GP-BUCKET
416E Single Tilt Backhoe Loader BWC00001-UP (MACHINE) POWERED BY C4.4 Engine »
246-9318
LINES GP-BUCKET
416E Backhoe Loader Single Tilt LMS00001-UP (MACHINE) POWERED BY C4.4 Engine »
246-9318
LINES GP-BUCKET
Caterpillar parts catalog:
Parts lines Caterpillar catalog:
2515855
LINES GP-MULTIPURPOSE BUCKET
414E, 416D, 416E, 420D, 420E, 430D, 430E
414E, 416D, 416E, 420D, 420E, 430D, 430E
2474885
LINES GP-FUEL FILTER
3054C, 414E, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 914G, C4.4, IT14G
3054C, 414E, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 914G, C4.4, IT14G
3151369
LINES GP-POWER TRAIN COOLER
416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
2573920
LINES GP-RIDE CONTROL
416E, 422E, 428E, 432E, 434E, 442E, 444E
416E, 422E, 428E, 432E, 434E, 442E, 444E
2473267
LINES GP-EXTENDABLE STICK
416E, 420E, 422E, 428E, 432E, 434E
416E, 420E, 422E, 428E, 432E, 434E
2143751
LINES GP-TRANSMISSION COOLER
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
2029130
LINES GP-CONNECTING
416E, 63
416E, 63
2475360
LINES GP-FUEL
414E, 416E, 422E
414E, 416E, 422E
7V2083
LINES GP-PUMP
140, D4E, D4E SR
140, D4E, D4E SR
1308909
LINES GP-FUEL FILTER
D8L, D9N, D9R
D8L, D9N, D9R
2519363
LINES GP-FUEL INJECTION
572R II, D7R II
572R II, D7R II
1069471
LINES GP-HYDROSTATIC
RR-250, SS-250
RR-250, SS-250
3090780
LINES GP-HYDRAULIC
120M, 120M 2, 12M
120M, 120M 2, 12M