LINES GP-FUEL INJECTION 3404176 - Caterpillar

3404176 LINES GP-FUEL INJECTION Caterpillar parts 3516B, 789D

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Sunsong 3404176 Power Steering Return Line Hose Assembly

$21.47

28 Mar 2025

US: USAutopartsCar

Sunsong 3404176 Power Steering Return Line Hose Assembly
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit

$12.39

19 Jun 2024

Amazon.com

Sunsong 3404176 Power Steering Return Line Hose Assembly
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit

$13.46

23 Mar 2023

Amazon.com

Sunsong 3404176 Power Steering Return Line Hose Assembly
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit

Compatible equipment models: 3404176:

INDUSTRIAL ENGINE 3516B

TRUCK 789D Caterpillar

Information:

Illustration 2 g00501596
Remove yoke assembly (3) from the rear differential. Yoke assembly (3) is a slip fit.
Illustration 3 g00501626
Remove bolts (4) from the junction blocks on each side of the rear main frame.
Illustration 4 g00501628
Disconnect tube assembly (5) that is connected to the grease fitting on top of the front support.
Fasten a suitable floor jack (8) to front support (7) .
Remove bolts (6), the nuts and washers that attach front support (7) to the rear main frame.
Remove the front support from the differential. The weight of the front support is 102 kg (224 lb).
Illustration 5 g00501647
Remove the bolts and washers that attach the retainer to the front support. Remove the retainer and the gasket from the front support.
Remove O-ring seals (10) and sleeve bearing (9) from the front support.
If necessary, remove the two locating dowels from the front support.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 4C-6486 Stand 2
8S-7621 Tube 2
8S-7625 Collar 2
8S-8048 Saddle 2
8S-7650 Cylinder 2
9U-6727 Hose Group 1
3S-6224 Electric Hydraulic Pump 1
8S-7615 Pin 4
Illustration 6 g00501835
Install the alignment dowels in the front support. The dowels should extend 55.6 1.5 mm (2.19 .06 inch) above the outside surface of the front support.
Install sleeve bearing (3) in the front support. Sleeve bearing (3) should make contact with the counterbore in the front support.
Install two O-ring seals (4) in the front support. Put a thin coat of 1P-0808 Multipurpose Grease on O-ring seals (4) and sleeve bearing (3) .
Install the gasket and the retainer on the front support. Install the washers and the bolts that hold the retainer in position.
Illustration 7 g00501842
Fasten a suitable floor jack (8) to front support (7). Install the front support on the rear differential.
Install bolts (6), the washers, and the nuts that hold the front support to the rear main frame. Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Connect tube assembly (5) to the grease fitting. The grease fitting is located on the top of the front support.
Illustration 8 g00501846
Install bolts (9) in the junction blocks. The junction blocks are located on each side of the rear main frame.
Illustration 9 g00501849
Install yoke assembly (10) on the rear differential. Yoke assembly (10) is a slip fit.
Illustration 10 g00501855
Use Tooling (A) in order to lower the machine to the floor.End By: Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) - Remove and Install".