AVSPARE.COM
parts catalog

LINES GP-PILOT 4415534 - Caterpillar



4415534 LINES GP-PILOT Caterpillar parts LINES
Rating:
71
Alternative (cross code) number:
CA4415534
441-5534
4415534
Caterpillar 4415534 LINES GP-PILOT

Buy LINES GP-PILOT 4415534 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Introduction
This instruction is to be used when replacing an original cylinder block that has cylinder liner counterbores, with a 0R2077 Remanufactured Short Block Group. The cylinder block in the Remanufactured Short Block Group MAY or may NOT have cylinder liner counterbores.If the original cylinder block and the Remanufactured Short Block both HAVE counterbored cylinder liners:* Refer to the Parts Book for the correct cylinder head gasket, seals, etc., that are needed to make the installation.If the Remanufactured Short Block does NOT have counterbored cylinder liners, and the original cylinder head from a non-spacer plate cylinder block is to be used again:* Additional parts (spacer plate, spacer plate gasket, seals and head gasket) will be needed for cylinder head installation. These parts are included with a spacer plate short block group. These parts are included with a spacer plate short block group.Because of the oil supply that is needed for the cylinder head valve mechanism, use ONLY the spacer plate and other additional parts that are INCLUDED, if an original cylinder head (from counterbored liner cylinder block) is to be installed on a Remanufactured Short Block.Refer to Additional Parts Included With Spacer Plate Short Block for the parts that are included. Reference: Service Manual Parts BookOperation and Maintenance Guide.Special Instruction SEHS8914 ... Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks
It is our recommendation to ALWAYS follow the Pressure Lubrication Procedures, as outlined in the above Special Instruction, BEFORE the engines initial start-up.
A remanufactured engine and short blocks MUST have adequate lubrication during the first few seconds of engine cranking and engine start.An engine start WITHOUT this lubrication can cause engine component(s) damage.Engine Assembly
1. Clean the protective coating from all parts in the short block group. After installation of the camshaft, put clean engine oil on the cylinder liner walls and the lifters. Turn the crankshaft several revolutions to get a good distribution of lubricant on these parts.2. Before further installation of parts on the new short block:* Measure crankshaft end clearance.* Inspect cylinder head for flatness.Refer to Specifications in the Service Manual.3. The spacer plate gasket, spacer plate and head gasket MUST be clean and dry. Do NOT use a gasket sealant.The 9Y1798 Seals(s) and 7N8018(s) Seals must be installed BEFORE cylinder head installation. Correct Sleeve/Dowel or Plug/Dowel Identification
Refer to location (A) on original cylinder block. Drive the dowel to the dimension shown.The part

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
MH3022 Wheeled Excavator Material Handler FB300001-UP (MACHINE) POWERED BY C7.1 Engine
MH3024 Wheeled Excavator Material Handler FB500001-UP (MACHINE) POWERED BY C7.1 Engine
MH3024 Wheeled Excavator Material Handler FB700001-UP (MACHINE) POWERED BY C7.1 Engine
MH3026 Wheeled Excavator Material Handler FB900001-UP (MACHINE) POWERED BY C7.1 Engine
MH3024 Wheeled Excavator Material Handler FM400001-UP (MACHINE) POWERED BY C7.1 Engine
MH3022 Wheeled Excavator Material Handler FM200001-UP (MACHINE) POWERED BY C7.1 Engine


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.