AVSPARE.COM
parts catalog

LINES GP-RIPPER 4Z9308 - Caterpillar



4Z9308 LINES GP-RIPPER Caterpillar parts D11R LINES
Rating:
40
Alternative (cross code) number:
CA4Z9308
4Z-9308
4Z9308
Caterpillar 4Z9308 LINES GP-RIPPER

Buy LINES GP-RIPPER 4Z9308 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z9308:

TRACK-TYPE TRACTOR  D11R   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 3 g00765339
P2 ECM connector
Thoroughly inspect ECM engine harness connector J2/P2 and the suspect sensor connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the sensor connector and the ECM connector that are associated with the active diagnostic code.
Verify that the latch tab of the connector is properly latched and that the latch tab of the connector has returned to the fully latching position.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the sensor to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and the wiring is good. Proceed to Test Step 3.
Not OK - There is a problem with the connectors and the wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 3. Verify That The Diagnostic Code Is Still Active
Place the engine control in the ON mode. Wait at least 15 seconds for activation of the diagnostic codes.
Access the "Active Diagnostic Code" screen of the electronic service tool. Check for active diagnostic codes.
Determine if the problem is related to an open circuit diagnostic code or a short circuit diagnostic code. Expected Result:A short circuit diagnostic code or an open circuit diagnostic code is active.Results:
Short Circuit - A short circuit diagnostic code is active at this time. Proceed to Test Step 4.
Open Circuit - An open circuit diagnostic code is active at this time. Proceed to Test Step 5.Test Step 4. Disconnect The Sensor In Order To Create An Open Circuit
Place the engine control in the OFF/RESET mode.
Disconnect the sensor connector of the sensor with the short circuit diagnostic code.
Place the engine control in the ON mode. Wait at least 15 seconds for activation of the diagnostic codes.
Access the "Active Diagnostic Code" screen of the electronic service tool. Check for an active open circuit diagnostic code. Expected Result:An open circuit diagnostic code for the disconnected sensor is now active.Results:
OK - A short circuit diagnostic code was active before disconnecting the sensor. An open circuit diagnostic code became active after disconnecting the sensor. Proceed to Test Step 6.
Not OK - There is a short circuit between the sensor harness connector and the ECM. Leave the sensor disconnected. Proceed to Test Step 7.Test Step 5. Create A Short Circuit Between The Signal And The Common Terminals At The Sensor Connector
Place the engine control in the ON mode.
Fabricate a jumper wire 150 mm (6 inch) long. Crimp a Deutsch terminal to both ends of the wire.
Monitor the "Active Diagnostic Code" screen before installing the jumper wire and after installing the jumper wire.
Install the jumper on the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D11R Custom Parts Manual Track-Type Tractor 8ZR00001-UP (MACHINE) POWERED BY 3508 Engine


Parts lines Caterpillar catalog:

2387590 LINES GP-WATER
773F, 775F, 777C, 777D, 777F, 844H, 990H, 993K, AD55B, AD60, D10T, D11R, D11T
6N8492 LINES GP-AFTERCOOLER WATER
235B, 235C, 235D, 3126, 330, 330 FM L, 330 L, 3306, 3306B, 330B, 330B L, 545, 973, 973C, W330B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.