5389922 LINES GP-HEATER Caterpillar parts
Rating:
Alternative (cross code) number:
CA5389922
538-9922
5389922
CA5389922
538-9922
5389922
Information:
Assembly Procedure
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many internal parts are not available for this component. Care must be taken during disassembly and assembly in order to prevent damage to unavailable parts.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01265789
Typical Example
Check O-ring seal (13) for wear or for damage. If necessary, replace O-ring seal (13) .
Illustration 2 g01265787
Typical Example
Install housing (11). Install bolts (10). If wiper (12) is worn or damaged replace the clean gas induction valve. Install O-ring seal (9) .
Illustration 3 g01265786
Install O-ring seals (8) onto valve (7). Install valve (7). Tighten valve (7) to a torque of 50 5 N m (37 4 lb ft). Install coil assembly (6) and nut (5). Tighten nut (5) to a torque of 20 3 N m (15 2 lb ft).
Illustration 4 g01301878
Install cover (2) onto clean gas induction valve (3). Install bolts (1) .End By: Install the clean gas induction valve. Refer to Disassembly and Assembly, "Clean Gas Induction Valve - Install".
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many internal parts are not available for this component. Care must be taken during disassembly and assembly in order to prevent damage to unavailable parts.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01265789
Typical Example
Check O-ring seal (13) for wear or for damage. If necessary, replace O-ring seal (13) .
Illustration 2 g01265787
Typical Example
Install housing (11). Install bolts (10). If wiper (12) is worn or damaged replace the clean gas induction valve. Install O-ring seal (9) .
Illustration 3 g01265786
Install O-ring seals (8) onto valve (7). Install valve (7). Tighten valve (7) to a torque of 50 5 N m (37 4 lb ft). Install coil assembly (6) and nut (5). Tighten nut (5) to a torque of 20 3 N m (15 2 lb ft).
Illustration 4 g01301878
Install cover (2) onto clean gas induction valve (3). Install bolts (1) .End By: Install the clean gas induction valve. Refer to Disassembly and Assembly, "Clean Gas Induction Valve - Install".
Caterpillar SIS machinery equipment:
Caterpillar SIS
MD6250 Rotary Blasthole Drill DN700001-UP (MACHINE) POWERED BY C27 Engine »
538-9922
LINES GP-HEATER
MD6250 Rotary Blasthole Drill DN800001-UP (MACHINE) POWERED BY C27 Engine »
538-9922
LINES GP-HEATER
MD6310 Rotary Blasthole Drill DLK00001-UP (MACHINE) POWERED BY C32 Engine »
538-9922
LINES GP-HEATER
MD6310 Rotary Blasthole Drill DLZ00001-UP (MACHINE) POWERED BY C32 Engine »
538-9922
LINES GP-HEATER
Caterpillar parts catalog:
Parts lines Caterpillar catalog:
5389579
LINES GP-DRAIN
Caterpillar
Caterpillar
5389578
LINES GP-DRAIN
Caterpillar
Caterpillar
5386213
LINES GP-RIPPER
Caterpillar
Caterpillar
5386212
LINES GP-ANGLE & TILT
Caterpillar
Caterpillar
5386210
LINES GP-LIFT CYLINDER
Caterpillar
Caterpillar
5384999
LINES GP-PILOT
Caterpillar
Caterpillar
5408579
LINES GP-BRAKE
Caterpillar
Caterpillar
5401241
LINES GP-TILT CYLINDER
Caterpillar
Caterpillar
5401240
LINES GP-ANGLE & TILT
Caterpillar
Caterpillar
5401238
LINES GP-CHARGE PRESSURE
Caterpillar
Caterpillar
5391891
LINES GP-AIR COMPRESSOR
Caterpillar
Caterpillar
5391890
LINES GP-AIR COMPRESSOR
Caterpillar
Caterpillar