7C3335 LINES GP-AIR Caterpillar parts
120H NA, 135H, 135H NA, 3116, 320 L, 322, 322 FM L, 322 LN, 613C II, AP-1000, CP-563, E200B, E240C, EL240B, M318, M320
Rating:
Alternative (cross code) number:
CA7C3335
7C-3335
7C3335
CA7C3335
7C-3335
7C3335
ASPHALT PAVER, WHEELED EXCAVATOR,
Compatible equipment models: 7C3335:
Information:
each of the following four functions.1. Program a new ECM. - When an ECM is replaced, the System Configuration Parameters must be programmed into the new ECM. For a new ECM these parameters can be programmed once without factory passwords, thereafter these parameters are protected by factory passwords.2. Read customer passwords. - If the owner loses his customer passwords, he will not be able to program Customer Specified Parameters. Using factory passwords, one can read customer passwords, then use those customer passwords to program Customer Specified Parameters.3. Clear certain diagnostic codes. - Diagnostic Code 190-00 (Engine Overspeed Warning) requires factory passwords to clear once it is logged.
Installing an ECM with a 3400 Marine Engine Personality Module on another engine (or the reverse) will damage the engine. Be sure the Personality Module is correct for your engine.
To obtain factory passwords, proceed as if you already had the password. At some point, if factory passwords are truly needed, the ECAP or ET will request factory passwords and display the information required to obtain the passwords.Customer Passwords
If customer passwords have been entered, they are then required to change ANY Customer Specified Parameter. Customer Specified Parameters are those that affect engine rpm limits and power rating within a family. Refer to the Customer Specified Parameters for more detail on what parameters are customer programmable.The ECAP or ET Electronic Service Tools may change Customer Specified Parameters. To obtain customer passwords, contact the owner of the unit. If the owner has lost his passwords, customer passwords may be read using an Electronic Service Tool (factory passwords are required in order to read the customer passwords). Follow the procedure below.1. Use the Electronic Service Tool to access Read/Change System Configuration Parameters, then read customer parameters.2. When the Factory Passwords screen appears, record the information listed on the Factory Passwords Worksheet.3. Obtain the factory passwords. The information recorded above must be provided, and generates a permanent record at Caterpillar of the access.4. Enter the factory passwords from the Factory Passwords screen.5. When the Read Customer Passwords screen appears, record the customer passwords. The customer passwords may then be used to change Customer Specified Parameters.System Configuration Parameters are protected by factory passwords. Factory passwords are calculated on a computer system available only to Caterpillar dealers. Since factory passwords contain alphabetic characters, only an ECAP or ET Electronic Service Tool may change System Configuration Parameters. System Configuration Parameters affect power family or emissions.Customer Specified Parameters are protected by customer passwords. The customer passwords are programmed by the customer. Refer to Programmable Parameters, for more details when passwords are needed and how to obtain them.ECM Replacement Procedure; Replacing The Electronic Control Module With A New ECM
The Electronic Control Module (ECM) is the heart of the electronic control system used on the 3408 and 3412 High Performance Marine Engine. The ECM contains no moving parts, has a very high reliability rating and replacement can be time consuming. Most problems occur in the connectors, wiring, or sensors. Follow the
Installing an ECM with a 3400 Marine Engine Personality Module on another engine (or the reverse) will damage the engine. Be sure the Personality Module is correct for your engine.
To obtain factory passwords, proceed as if you already had the password. At some point, if factory passwords are truly needed, the ECAP or ET will request factory passwords and display the information required to obtain the passwords.Customer Passwords
If customer passwords have been entered, they are then required to change ANY Customer Specified Parameter. Customer Specified Parameters are those that affect engine rpm limits and power rating within a family. Refer to the Customer Specified Parameters for more detail on what parameters are customer programmable.The ECAP or ET Electronic Service Tools may change Customer Specified Parameters. To obtain customer passwords, contact the owner of the unit. If the owner has lost his passwords, customer passwords may be read using an Electronic Service Tool (factory passwords are required in order to read the customer passwords). Follow the procedure below.1. Use the Electronic Service Tool to access Read/Change System Configuration Parameters, then read customer parameters.2. When the Factory Passwords screen appears, record the information listed on the Factory Passwords Worksheet.3. Obtain the factory passwords. The information recorded above must be provided, and generates a permanent record at Caterpillar of the access.4. Enter the factory passwords from the Factory Passwords screen.5. When the Read Customer Passwords screen appears, record the customer passwords. The customer passwords may then be used to change Customer Specified Parameters.System Configuration Parameters are protected by factory passwords. Factory passwords are calculated on a computer system available only to Caterpillar dealers. Since factory passwords contain alphabetic characters, only an ECAP or ET Electronic Service Tool may change System Configuration Parameters. System Configuration Parameters affect power family or emissions.Customer Specified Parameters are protected by customer passwords. The customer passwords are programmed by the customer. Refer to Programmable Parameters, for more details when passwords are needed and how to obtain them.ECM Replacement Procedure; Replacing The Electronic Control Module With A New ECM
The Electronic Control Module (ECM) is the heart of the electronic control system used on the 3408 and 3412 High Performance Marine Engine. The ECM contains no moving parts, has a very high reliability rating and replacement can be time consuming. Most problems occur in the connectors, wiring, or sensors. Follow the
Caterpillar SIS machinery equipment:
Caterpillar SIS
CS-563 & CP-563 VIBRATORY COMPACTORS 1YJ00001-00384 (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
AP-1000 Asphalt Paver 1HD00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
3116 Industrial Engine 4PG00001-UP »
7C-3335
LINES GP-AIR
3116 Industrial Engine 2WG00001-UP »
7C-3335
LINES GP-AIR
613CII WHEEL TRACTOR SCRAPER 8LJ00001-UP (MACHINE) »
7C-3335
LINES GP-AIR
320, 320L & 320N EXCAVATORS 3XK00001-00821 (MACHINE) »
7C-3335
LINES GP-AIR
320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
322L EXCAVATOR 9RL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
120H Motor Grader 4MK00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
135H Motor Grader 3YK00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
M318 Excavator 8AL00001-01019 (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
3116 Industrial Engine 5EN00001-UP »
7C-3335
LINES GP-AIR
3116 Industrial Engine 2MR00001-UP »
7C-3335
LINES GP-AIR
M320 Excavator 6WL00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
M318 Excavator 6ES00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
M320 Excavator 9PS00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
M318 Excavator 8SS00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
M318 Excavator 8AL01020-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
120H Series NA Motor Grader 6YN00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
135H Series NA Motor Grader BDJ00001-UP (MACHINE) POWERED BY 3116 Engine »
7C-3335
LINES GP-AIR
320, 320L TRACK-TYPE EXCAVATORS 1TL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
E240C, EL240C TRACK-TYPE EXCAVATORS 2RL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
322 322L TRACK-TYPE EXCAVATORS 7WL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP
E200B, EL200B TRACK-TYPE EXCAVATORS 6KF00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
E240B, EL240B TRACK-TYPE EXCAVATORS 5WG00001-UP (MACHINE) POWERED BY 3116 ENGINE »
7C-3335
LINES GP-AIR
Caterpillar parts catalog:
Parts lines Caterpillar catalog:
3587469
LINES GP-BOOM CYLINDER
336E, 336E L, 336E LH, 336E LN, 336F L
336E, 336E L, 336E LH, 336E LN, 336F L
2551803
LINES GP-PILOT
324D, 324D L, 325D, 329D, 329D L
324D, 324D L, 325D, 329D, 329D L
2138205
LINES GP-STICK
325B L, 325C, 325C L, 325D MH, M325B
325B L, 325C, 325C L, 325D MH, M325B
8N8507
LINES GP-AIR
3512
3512
1663308
LINES GP-RIPPER
120H, 12H, 135H, 140H, 143H, 160H, 163H, 16H
120H, 12H, 135H, 140H, 143H, 160H, 163H, 16H
3052946
LINES GP-HYDRAULIC
12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
1348611
LINES GP-AIR CONDITIONER
938G, IT38G
938G, IT38G
1385073
LINES GP-FRONT
330B, 330B L
330B, 330B L
6N9316
LINES GP-FUEL FILTER
3126, 3412, 3412D
3126, 3412, 3412D
9W1018
LINES GP-RIPPER
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II