7S9674 LINING Caterpillar parts
D8H, D8K
Rating:
Alternative (cross code) number:
CA7S9674
7S-9674
7S9674
CA7S9674
7S-9674
7S9674
Weight: 0.38 pounds 0 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-8665 Cylinder Liner Puller 1
B 2P-8260 Cylinder Liner Installer 1
C - Loctite LB 8632 Silicone Lubricant (1) -
- Loctite LB 8104 Silicone Lubricant (2) -
- Loctite LB 8801 Silicone Lubricant (3) -
- Loctite LB Superlube (4) -
(1) North America
(2) EAME
(3) Asia Pacific Division
(4) South AmericaStart By:
Remove pistons and connecting rods.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Place covers over the crankshaft journals to shield the journals from dirt and coolant.
Illustration 1 g06057772
Use Tooling (A) to remove cylinder liner (1).
Illustration 2 g06057795
Remove O-ring seals (2) and liner seal (3).Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Measure liner projection. Refer to Testing and Adjusting, "Cylinder liner projection".
Prepare cylinder liner (1) for installation. There are two types of seals that can be used on the cylinder liners.
Illustration 3 g06333167
Type 1
Illustration 4 g02248239
Type 1
Apply liquid soap on the grooves for O-ring seals (2) and on O-ring seals (2). Install O-ring seals (2) on cylinder liner (1). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (1).
Immediately install cylinder liner (1) before filler band (3) can expand.
Illustration 5 g06333198
Type 2
Liner seal (4) requires a machined chamfer at the top edge of the liner bore to install the liner seal.
A chamfer can be machined into the top edge of the bore in the block for the cylinder liner. Refer to Reuse and Salvage Guidelines, SEBF8255, "Reuse and Salvage for 3500 Engine Cylinder Blocks", Procedure to Chamfer Liner Bores for the correct procedure for machining the chamfer.Note: Liner seat inserts that include the chamfer are also available. Refer to Reuse and Salvage Guidelines, SEBF8255, "Reuse and Salvage for 3500 Engine Cylinder Blocks".
Ensure that the liner groove for liner seal (4) is clean and dry. Install liner seal (4) on cylinder liner (1). Apply a thin coat of Tooling (C) to the cylinder block on the machined chamfer to a distance of 5 mm (0.2 inch) below the machined chamfer. Apply Tooling (C) to liner seal (4).Note: Do not apply Tooling (C) to the liner flange or the top of the cylinder block.
Apply liquid soap on the grooves for O-ring seals (2) and on O-ring seals (2). Install O-ring seals (2) on cylinder liner (1). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-8665 Cylinder Liner Puller 1
B 2P-8260 Cylinder Liner Installer 1
C - Loctite LB 8632 Silicone Lubricant (1) -
- Loctite LB 8104 Silicone Lubricant (2) -
- Loctite LB 8801 Silicone Lubricant (3) -
- Loctite LB Superlube (4) -
(1) North America
(2) EAME
(3) Asia Pacific Division
(4) South AmericaStart By:
Remove pistons and connecting rods.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Place covers over the crankshaft journals to shield the journals from dirt and coolant.
Illustration 1 g06057772
Use Tooling (A) to remove cylinder liner (1).
Illustration 2 g06057795
Remove O-ring seals (2) and liner seal (3).Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Measure liner projection. Refer to Testing and Adjusting, "Cylinder liner projection".
Prepare cylinder liner (1) for installation. There are two types of seals that can be used on the cylinder liners.
Illustration 3 g06333167
Type 1
Illustration 4 g02248239
Type 1
Apply liquid soap on the grooves for O-ring seals (2) and on O-ring seals (2). Install O-ring seals (2) on cylinder liner (1). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (1).
Immediately install cylinder liner (1) before filler band (3) can expand.
Illustration 5 g06333198
Type 2
Liner seal (4) requires a machined chamfer at the top edge of the liner bore to install the liner seal.
A chamfer can be machined into the top edge of the bore in the block for the cylinder liner. Refer to Reuse and Salvage Guidelines, SEBF8255, "Reuse and Salvage for 3500 Engine Cylinder Blocks", Procedure to Chamfer Liner Bores for the correct procedure for machining the chamfer.Note: Liner seat inserts that include the chamfer are also available. Refer to Reuse and Salvage Guidelines, SEBF8255, "Reuse and Salvage for 3500 Engine Cylinder Blocks".
Ensure that the liner groove for liner seal (4) is clean and dry. Install liner seal (4) on cylinder liner (1). Apply a thin coat of Tooling (C) to the cylinder block on the machined chamfer to a distance of 5 mm (0.2 inch) below the machined chamfer. Apply Tooling (C) to liner seal (4).Note: Do not apply Tooling (C) to the liner flange or the top of the cylinder block.
Apply liquid soap on the grooves for O-ring seals (2) and on O-ring seals (2). Install O-ring seals (2) on cylinder liner (1). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Caterpillar parts catalog:
Parts lining Caterpillar catalog:
9H3493
LINING
583H, 977K, D8H, D9G
583H, 977K, D8H, D9G
5S1608
LINING
D8H
D8H
8M3854
LINING
D8H
D8H
4K1323
LINING
955H, 955K, 955L
955H, 955K, 955L
4K6769
LINING
955H, 955K, 955L
955H, 955K, 955L
6K6170
LINING (Drilled)
D3, D4D
D3, D4D
5S5658
LINING
977K, D5B, D6C
977K, D5B, D6C
9H3493
LINING
583H, 977K, D8H, D9G
583H, 977K, D8H, D9G
5V4245
LINING
955L
955L
5V4246
LINING
955L
955L
4V2245
LINING
931B, 941, D3B, D4C, D4E
931B, 941, D3B, D4C, D4E
4V2244
LINING
931B, 941, D3B, D4C, D4E
931B, 941, D3B, D4C, D4E