AVSPARE.COM
parts catalog

LINK A DRAG 0876520 - Caterpillar



0876520 LINK A DRAG Caterpillar parts LINK
Rating:
31
Alternative (cross code) number:
CA0876520
087-6520
0876520
Caterpillar 0876520 LINK A DRAG

Buy LINK A DRAG 0876520 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Measurement Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Plastigauge (Green) 0.025 to 0.076 mm (0.001 to 0.003 inch) 1
- Plastigauge (Red) 0.051 to 0.152 mm (0.002 to 0.006 inch) 1
- Plastigauge (Blue) 0.102 to 0.229 mm (0.004 to 0.009 inch) 1
- Plastigauge (Yellow) 0.230 to 0.510 mm (0.009 to 0.020 inch) 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Caterpillar does not recommend the checking of the actual clearances of the bearing shells particularly on small engines. Checking the actual clearances of the bearing shells may result in obtaining inaccurate results and damaging the bearing shell or the journal surfaces. Each Caterpillar bearing shell is quality checked for specific wall thickness.Note: The measurements should be within specifications and the correct bearings should be used. If the crankshaft journals and the bores for the block and the rods were measured during disassembly, no further checks are necessary. However, if the technician still wants to measure the bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals with small diameters if clearances are less than 0.10 mm (0.004 inch).
Lead wire, shim stock or a dial bore gauge can damage the bearing surfaces.
The technician must use Tooling (A) correctly. The following points must be remembered:
Ensure that the backs of the bearings and the bores are clean and dry.
Ensure that the bearing locking tabs are properly seated in the tab grooves.
The crankshaft must be free of oil at the contact points of Tooling (A).
Put a piece of Tooling (A) on the crown of the bearing that is in the cap. Note: Do not allow Tooling (A) to extend over the edge of the bearing.
Use the correct torque-turn specifications in order to install the bearing cap. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed. Note: Do not turn the crankshaft when Tooling (A) is installed.
Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling (A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration 1.
Illustration 1 g01152855
Typical Example
Remove all of Tooling (A) before you install the bearing cap. Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all parts of Tooling (A) are not the same width. Measure the major width in order to ensure that the parts are within the specification range. Refer to Specifications Manual, "Connecting Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct clearances.


Parts link Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.