0990723 LINK Caterpillar parts
311, 311B, 312, 312B, 320B, 320N, 322B L, 325, 325B L, E110B, E120B, E200B, E240C, EL240B
Rating:
Alternative (cross code) number:
CA0990723
099-0723
0990723
CA0990723
099-0723
0990723
Weight: 16 pounds 7 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$128.81
13 Feb 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Link RH 0990723 New
$77.39
14 Sep 2021
16.4464[7.40] Pounds
US: IronDT
CTP Caterpillar Link Rh (0990723)
CTP
CTP
13 Feb 2018
1700 Hundredths Pounds
CTP: CTP
0990723 Link RH Fits Caterpillar 312 322B L
Warranty
Warranty
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 0990723:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
178–8615 Engine Turning Tool(1) 1
(1) Can be used to turn crankshaft from the front of the engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The joint between the connecting rod and the connecting rod cap is produced by fracturing. The connecting rod assembly must be handled with care in order to avoid damage to the mating surfaces. The connecting rod assembly must be replaced if any damage occurs to the mating surfaces. New connecting rod assemblies come with the connecting rod caps bolted on the connecting rod.Use only a soft faced hammer to tap the connecting rod cap when separating the connecting rod cap from the connecting rod.Failure to use a soft faced hammer may result in damage to the fractured surfaces of the connecting rod assembly.
Note: Refer to Reuse and Salvage Guidelines, "Salvage Procedures for Connecting Rods".
Use Tooling (A) to turn the crankshaft until the connecting rod bearing cap is accessible.
Illustration 1 g01139029Note: Install the connecting rod bearings dry when clearance checks are performed. Apply clean engine oil to the connecting rod bearings for final assembly.
Remove the protective caps from the end of the connecting rod and install the upper half of connecting rod bearing (4). Ensure that the bearing tab engages with the slot in connecting rod (3).
Pull the piston and connecting rod assembly onto the crankshaft.
Install the lower half of connecting rod bearing (5) into connecting rod cap (1). Ensure that the bearing tab engages with the slot in connecting rod cap (1).Note: Do not place the fractured faces of the connecting rod cap on any surface. The connecting rod cap must be laid flat on the side to prevent damage to the fractured faces of the connecting rod cap.Note: Ensure that the number on the connecting rod cap matches the number on the connecting rod. Make sure that both of the numbers are located on the same side.
Install connecting rod cap (1) and connecting rod cap bolts (2).
Check the bearing clearance. Refer to Disassembly and Assembly, "Bearing Clearance - Check".
Tighten connecting rod cap bolts (2) to a torque of 50 5 N m (37 3 lb ft).
Place an index mark on each connecting rod cap bolt (2). Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Use Tooling (A) to rotate the crankshaft to ensure that the crankshaft turns freely.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
178–8615 Engine Turning Tool(1) 1
(1) Can be used to turn crankshaft from the front of the engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The joint between the connecting rod and the connecting rod cap is produced by fracturing. The connecting rod assembly must be handled with care in order to avoid damage to the mating surfaces. The connecting rod assembly must be replaced if any damage occurs to the mating surfaces. New connecting rod assemblies come with the connecting rod caps bolted on the connecting rod.Use only a soft faced hammer to tap the connecting rod cap when separating the connecting rod cap from the connecting rod.Failure to use a soft faced hammer may result in damage to the fractured surfaces of the connecting rod assembly.
Note: Refer to Reuse and Salvage Guidelines, "Salvage Procedures for Connecting Rods".
Use Tooling (A) to turn the crankshaft until the connecting rod bearing cap is accessible.
Illustration 1 g01139029Note: Install the connecting rod bearings dry when clearance checks are performed. Apply clean engine oil to the connecting rod bearings for final assembly.
Remove the protective caps from the end of the connecting rod and install the upper half of connecting rod bearing (4). Ensure that the bearing tab engages with the slot in connecting rod (3).
Pull the piston and connecting rod assembly onto the crankshaft.
Install the lower half of connecting rod bearing (5) into connecting rod cap (1). Ensure that the bearing tab engages with the slot in connecting rod cap (1).Note: Do not place the fractured faces of the connecting rod cap on any surface. The connecting rod cap must be laid flat on the side to prevent damage to the fractured faces of the connecting rod cap.Note: Ensure that the number on the connecting rod cap matches the number on the connecting rod. Make sure that both of the numbers are located on the same side.
Install connecting rod cap (1) and connecting rod cap bolts (2).
Check the bearing clearance. Refer to Disassembly and Assembly, "Bearing Clearance - Check".
Tighten connecting rod cap bolts (2) to a torque of 50 5 N m (37 3 lb ft).
Place an index mark on each connecting rod cap bolt (2). Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Use Tooling (A) to rotate the crankshaft to ensure that the crankshaft turns freely.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar parts catalog:
Parts link Caterpillar catalog:
311, 311B, 312, 312B, 313B, 320B, 320C, 320N, 322B L, 325, 325B L, E110B, E120B, E200B, E240C, EL240B
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 321B, 321C, 322, 322 FM L, 322B L, 322C, 325, 325 L, 325...
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 321B, 321C, 322, 322 FM L, 322B L, 322C, 325, 325 ...
311C, 312B L, 312C, 312C L, 313B, 314C, 320C, 322B, 322B L, 322C, 322C FM, 323D L, 325C, 325D, 330B L, 330C, 330C L
315B, 315B L, 317B LN, 318B, 320B, 325B L, 330B L, 345B L
318B, 320B, 322, 325, 325 L, 325 LN, 325B L, 330B L, 345B L
313B, 320C, 322B L, 322C, 322C FM, 325C, 330B L
320 L, 320B, 320C, 320N, 325, 325 LN, 325B L, 325C, 325C FM, 330, 330 FM L, 330C L, 345B II, 350, 350 L, 5080
320 L, 320B, 320N, 325, 325 LN, 325B, 325B L, 330, 330 FM L, 345B L, 350, 350 L, 5080
320 L, 320B, 320N, 325, 325 LN, 325B, 325B L, 330, 330 FM L, 345B L, 350, 350 L, 375, 5080
322B L, 322C, 325, 325 L, 325 LN, 325B L, 325C, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 385B, 385C L
322B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330B L
1478487
LINK-SHAFT
312, 312B L, 312C
312, 312B L, 312C
1090, 1190T, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U,...
311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U, 320C, 320C F...
311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U, 320C, 320C F...
1090, 1190T, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U,...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 321B, 321C, 322, 322 FM L, 322B L, 322C, 325, 325 ...
1175506
LINK & BEARING AS
315, 315B, 315B L, 317, 317B LN
315, 315B, 315B L, 317, 317B LN
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 321B, 321C, 322, 322 FM L, 322B L, 322C, 325, 325 L, 325...
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320B, 322 FM L, 322B L, 322B LN, 325 L, 325B L, 330, 330 L, 330B L, 345B II, 345B L, 350, 350 L, 375, 375 L, 5080
311, 311B, 312, 312B, 313B, 320B, 320C, 320N, 322B L, 325, 325B L, E110B, E120B, E200B, E240C, EL240B
1012186
LINK AS
311, 311B, 312, 312B, 312B L, 313B
311, 311B, 312, 312B, 312B L, 313B