1122900 LINK AS-BEARING Caterpillar parts
325B L, 330, 330 FM L
Rating:
Alternative (cross code) number:
CA1122900
112-2900
1122900
CA1122900
112-2900
1122900
Weight: 273 pounds 123 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$31.31
28 Apr 2019
OSG: OSG
PART NO. OSG1122900 1/2-20 General Purpose Straight Flute Hand Tap 4-Flute, High Speed Steel, Bright Finish, H3 Limit, OSG 1122900, Series 101
Number on catalog scheme:
3
For full view, you need register
Information:
7. Install two 3/8"-16 NC guide bolts for each bearing cap (6). Install caps (6) in the case with their original shims (7) until they are even with the inside surface of the case.
The dowel in the end of the swashplate is very hard and is easily broken. Extra caution must be used when the swashplate is installed in the case to prevent damage to the dowel. The dowel must extend beyond the swashplate 4.00 0.25 mm (.157 .010 in.).
8. Install tooling (F) on swashplate (8), and fasten a hoist. Put the swashplate in position in the case between the bearing caps. Carefully push the caps into position to hold the swashplate. Install three bolts at even spaces in each cap. The longer bolts go in the bottom cap.
If swashplate (8) becomes tight between the bearing caps while the bolts in the caps are tightened, stop and install more shims under the bearing caps. There must be end play in the swashplate at all times during the installation of the bearing caps. The bearings for the swashplate can be damaged if too much preload is put on the bearings.
9. While the swashplate is turned in the case, evenly tighten the bolts in the bearing caps to a torque of 45 5 N m (33 4 lb.ft.). Turn the case so the swashplate is in a vertical position as shown. 10. Install tooling (G) as shown to measure the end play of the swashplate. Carefully use a pry bar to move the swashplate up and down and measure the end play. The end play must be 0.08 0.05 mm (0.003 0.002 in.).11. Remove the caps, shims and swashplate from the case. Measure the thickness of the original shim packs, and add or subtract shims to get the correct end play in the swashplate. Divide the shim packs evenly between the top and bottom caps. Install the swashplate and bearing caps with the correct shim packs in the case again, and check the swashplate end play. When the end play is correct, remove the bearing caps and swashplate from the case. 12. Install dowel (10) and plate (9) on the swashplate with the dowel hole in plate (9) in alignment with dowel (10). 13. Use a wire to be sure the oil hole in each piston (11) and slipper (12) is open. 14. Install the pistons in retraction plate (14), and use an O-ring seal (15) to hold the pistons together. Install the pistons and retraction plate on the swashplate. Put retraction bearings (16) with original shims (13) in position on the swashplate, and install the old bolts that hold them in place. Tighten the bolts to a torque of 12.5 1 N m (9.5 1 lb.ft.) for a 943 swashplate. Tighten the bolts to a torque of 25 7 N m (18 5 lb.ft.) for a 953 swashplate. Remove O-ring seal (15). 15. Use a thickness gauge to measure
The dowel in the end of the swashplate is very hard and is easily broken. Extra caution must be used when the swashplate is installed in the case to prevent damage to the dowel. The dowel must extend beyond the swashplate 4.00 0.25 mm (.157 .010 in.).
8. Install tooling (F) on swashplate (8), and fasten a hoist. Put the swashplate in position in the case between the bearing caps. Carefully push the caps into position to hold the swashplate. Install three bolts at even spaces in each cap. The longer bolts go in the bottom cap.
If swashplate (8) becomes tight between the bearing caps while the bolts in the caps are tightened, stop and install more shims under the bearing caps. There must be end play in the swashplate at all times during the installation of the bearing caps. The bearings for the swashplate can be damaged if too much preload is put on the bearings.
9. While the swashplate is turned in the case, evenly tighten the bolts in the bearing caps to a torque of 45 5 N m (33 4 lb.ft.). Turn the case so the swashplate is in a vertical position as shown. 10. Install tooling (G) as shown to measure the end play of the swashplate. Carefully use a pry bar to move the swashplate up and down and measure the end play. The end play must be 0.08 0.05 mm (0.003 0.002 in.).11. Remove the caps, shims and swashplate from the case. Measure the thickness of the original shim packs, and add or subtract shims to get the correct end play in the swashplate. Divide the shim packs evenly between the top and bottom caps. Install the swashplate and bearing caps with the correct shim packs in the case again, and check the swashplate end play. When the end play is correct, remove the bearing caps and swashplate from the case. 12. Install dowel (10) and plate (9) on the swashplate with the dowel hole in plate (9) in alignment with dowel (10). 13. Use a wire to be sure the oil hole in each piston (11) and slipper (12) is open. 14. Install the pistons in retraction plate (14), and use an O-ring seal (15) to hold the pistons together. Install the pistons and retraction plate on the swashplate. Put retraction bearings (16) with original shims (13) in position on the swashplate, and install the old bolts that hold them in place. Tighten the bolts to a torque of 12.5 1 N m (9.5 1 lb.ft.) for a 943 swashplate. Tighten the bolts to a torque of 25 7 N m (18 5 lb.ft.) for a 953 swashplate. Remove O-ring seal (15). 15. Use a thickness gauge to measure
Caterpillar parts catalog:
Parts link Caterpillar catalog:
322C FM, 324D FM, 324D FM LL, 325B L, 325C, 325C FM
311, 311B, 312, 312B, 313B, 320B, 320C, 320N, 322B L, 325, 325B L, E110B, E120B, E200B, E240C, EL240B
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 321B, 321C, 322, 322 FM L, 322B L, 322C, 325, 325 L, 325...
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 321B, 321C, 322, 322 FM L, 322B L, 322C, 325, 325 ...
320 L, 320B, 320C, 320N, 325, 325 LN, 325B L, 325C, 325C FM, 330, 330 FM L, 330C L, 345B II, 350, 350 L, 5080
320 L, 320B, 320N, 325, 325 LN, 325B, 325B L, 330, 330 FM L, 345B L, 350, 350 L, 375, 5080
322B L, 322C, 325, 325 L, 325 LN, 325B L, 325C, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 385B, 385C L
322B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330B L
330, 330 FM L, 330 L, 330B L, 330C, 330C L
1156296
LINK AS
330
330
1156295
LINK
330
330
1054745
LINK
325B L, 330, 330 FM L, 330B L
325B L, 330, 330 FM L, 330B L
1054746
LINK
325, 325B L, 330, 330 FM L, 330B L
325, 325B L, 330, 330 FM L, 330B L
1439254
LINK AS
325B L
325B L
1439253
LINK AS
325B L
325B L
325, 325 L, 325B L
4I4724
LINK AS
330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L
330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L
1116076
LINK & BEARING AS
330, 330 FM L, 330B L
330, 330 FM L, 330B L
330, 330 FM L, 330 L, 330B L, 330C, 330C L