1483307 LINK Caterpillar parts
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 385C
Rating:
Alternative (cross code) number:
CA1483307
148-3307
1483307
CA1483307
148-3307
1483307
Weight: 103 pounds 46 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement Parts for Snow Removal UTV ATV Cart Machinery for 1483307 Link for Caterpillar Models Model-DFC589-Gl52149
Generic Premium replacement parts for lawn and garden, snow removal, UTV, ATV, and golf cart equipment, built to last || Crafted from high-quality, weather-resistant materials for durability in any conditions || Easy-to-install parts that fit perfectly, saving you time and effort on maintenance || Ideal for extending the life and efficiency of your machinery, reducing the need for costly replacements || Suitable for a wide range of brands and models, providing flexible options for various equipment types
Generic Premium replacement parts for lawn and garden, snow removal, UTV, ATV, and golf cart equipment, built to last || Crafted from high-quality, weather-resistant materials for durability in any conditions || Easy-to-install parts that fit perfectly, saving you time and effort on maintenance || Ideal for extending the life and efficiency of your machinery, reducing the need for costly replacements || Suitable for a wide range of brands and models, providing flexible options for various equipment types
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 1483307:
Information:
Illustration 1 g01080908
Schematic of Solenoid Valve (2) for the Counterbalance ValveThis diagnostic code is associated with the solenoid valve (2) for the counterbalance valve. The FMI 05 means that the ECM has determined that an open in the circuit exists.The possible causes of this diagnostic code are listed below:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2324 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active the hydraulic control system will default to the "Service Mode" state.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire Y926-YL) to contact 2 (wire H807-YL).
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the CID 2324 FMI 05.Expected Result:The CID 2324 FMI 05 diagnostic code changes to FMI 06. This may take up to 30 seconds to change after the jumper wire is installed.Results:
YES - The CID 2324 FMI 05 diagnostic code changes to FMI 06. The circuit is correct. Repair: The solenoid has failed. Repeat this test step in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.Test Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector(s) from the ECM.
The jumper wire that was installed in the previous test step remains in place.
At the machine harness connector, measure the resistance from signal contact J2-5 (wire Y926-YL) to contact J2-4 (wire H807-YL).Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is less than 5 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire Y926-YL or in wire H807-YL of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 2324 FMI 05.Expected Result:The CID 2324 FMI 05 is active.Results:
YES - The CID 2324 FMI 05 is active. The diagnostic code has
Cat SIS web machinery list:
Parts link Caterpillar catalog:
330D L, 330D MH, 345C, 345C L, 345C MH, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 568 FM LL
322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D L, 324D LN, 326D L, 329D L, 345D L, OEMS
325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 345C, OEMS
1090, 1190T, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U,...
311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U, 320C, 320C F...
311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U, 320C, 320C F...
1090, 1190T, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U,...
2736806
LINK AS
345C, 345C L, 345D L
345C, 345C L, 345D L
3342278
LINK-MASTER
349E L, 349E L VG, 349F L
349E L, 349E L VG, 349F L
3660442
LINK & BEARING AS
349E L, 349E L VG, 349F L
349E L, 349E L VG, 349F L
3415069
LINK AS
349E
349E
345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 385C
345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 385C
4574716
LINK AS-GRAPPLE
CTV20
CTV20
4380655
LINK AS-GRAPPLE
CTV20
CTV20
3953433
LINK AS-GRAPPLE
CTV20
CTV20
3966846
LINK AS-GRAPPLE
CTV20
CTV20
3059361
LINK-TRACK
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E L, 349E L VG
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E L, 349E L VG
3059362
LINK-TRACK
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E L, 349E L VG
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E L, 349E L VG
2964360
LINK-TRACK
385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L
385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L
2964359
LINK-TRACK
385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L
385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L
2512655
LINK & BEARING AS
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E L VG, 365C, 365C L, 385C
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E L VG, 365C, 365C L, 385C
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 385C