LINK AS-TILT 1869866 - Caterpillar

Affected Product
Model & Identification Number
D6H (4RC1903-4253 6FC558-4079 3ZF460-4381 3YG334-4254 6CF4141-4161 , 6CF4163 5HF1-4167 2TG415-557 4LG567-4314 1FJ1-4127 )
D7H (79Z1861-4366 80Z739-806 5BF479-4234 , 5BF4236 4FG321-4116 )
14G (03L201-228 96U7257-8445 )
140G (50H1301, 50H1304-1602 72V11007-14367 )
CH65 (7YC1-2061)
235C (5AF1-1699, 5AF1703 3WG1-282 4DG1-730 2PG1-801 )
615C (5TF1-564)
637E (Scraper Engine Only) (1JB576-724, 1JB494, 1JB496, 1JB498-511, 1JB513-515, 1JB518-519; 1HB406-437, 1HB439-477, 1HB479-559, 1HB562-567, 1HB569-575, 1HB579-581, 1HB583-584; 1LB617-771 )
627E (Scraper Engine Only) (05A9551-9552, 05A9604-9605, 05A9699-9700, 05A9706; 6EB526-729 ; 6GB619-777 ; 6FB515-701 ; 6HB608-781 ; 7CG1-810 , 7CG812-813, 7CG815-816, 7CG819-821; 3WJ1-101 )
815B (17Z881-1378)
816B (15Z769-1182)
966E (05A9485, 05A9488-9489, 05A9506; 99Y5433-7389 ; 94X6859-9778 )
966F (4YG1-803; 3XJ1-1247 )
3306 (63Z13587-20292; 64Z9392-10470 )
Parts Needed
7 4B4274 Washer*2 7E6452 Damper*1 7E9094 Clamp*1 7E9095 Clamp*1 6I0341 Line Assembly*1 6I0342 Line Assembly*1 6I0343 Line Assembly*1 6I0344 Line Assembly*1 6I0345 Line Assembly*1 6I0346 Line Assembly*6 9N3388 Screw1 4P9330 Lines Gp (3306 Vehicular & Truck Engines) (Except Ford Trucks)1 4P9331 Lines Gp (3306 Vehicular Applications Only)1 4P9332 Lines Gp (3306 Truck Engines Only) (Except Ford Trucks) 22 1W9168 Clamp*18 1W9169 Clamp*1 1005673 Lines Gp (3306 Truck Engines in Ford Trucks)1 1005674 Lines Gp (3306 Truck Engines in Ford Trucks)*For use on D7H, 627E and 637E Scraper Engines which are equipped with the Laminated Thermoshield fuel injection lines.These engines have a water-cooled center section turbocharger and a heat shield around the turbocharger's turbine housing.The following parts are for replacing the existing oil drain tube on 627E and 637E only. These parts are required only with the Laminated Thermoshield fuel injection lines.
1 1S4810 Gasket1 1W8057 Tube Assembly1 9M4849 Seal - O-ring1 9N5328 AdapterAction Required
D6H and D7H Tractors, 14G and 140G Motor Graders, Challenger 65 Tractors, 235C Excavators, 615C, 627E and 637E Scrapers, 815B and 816B Compactors, 966E and 966F Wheel Loaders
Replace the existing #1-#4 fuel lines with a new 4P9330 Lines Group and the existing #5 & #6 fuel lines with a new 4P9331 Lines Group except when equipped with Laminated Thermoshield fuel lines.
On D7H, 627E and 637E Scraper Engines only, it is necessary to determine if the machine is equipped with the standard fuel lines or the optional Laminated Thermoshield fuel lines. These engines have a water-cooled center section turbocharger and heat shield around the turbocharger's turbine housing.
If equipped with Laminated Thermoshield fuel lines, do not remove the 7E8530 Rear Support Bracket, 7E9028 Mid Support Bracket, 7E1356 #1 Fuel Line Support Bracket, 7E5887 #2 Fuel Line Bracket and 7E5887 #3 Fuel Line Bracket from the engine. Loosely assemble the six new fuel lines. Use new clamp assemblies and place them at the locations shown in Illustration 1. Tighten all the fuel lines as described in the September 11, 1989 Service Magazine. Tighten the fuel line nuts to the injector and injection pump only after all brackets have been tightened.
In addition to replacing the fuel lines on 627E and 637E, replace the existing oil drain tube with a new 1W8057 Tube, 9N5328 Adapter, 9M4849 Seal and 1S4810 Gasket.
If an engine has the Laminated Thermoshield lines installed without the watercooled turbine housing and heat shield, use the 6I0341, 6I0342, 6I0343, 6I0344, 6I0345, 6I0346 Fuel Lines. Do